Top 10 best induction heater with fan: Which is the best one in 2020?

It took days of going through more than a thousand customer reviews and conducting expert researches to narrow down the list. Weve included a comparison table below to give you a quick summary of our top 10 induction heater with fan. Its followed by an in-depth review of each induction heater with fan. Hopefully, once you are done reading this article, you will be well informed about induction heater with fan and be able to select the right induction heater with fan for you without any hesitations.

Best induction heater with fan

Related posts:

Best induction heater with fan reviews

1. 4-Blade Heat Powered Stove Fan for Wood / Log Burner/Fireplace increases 80% more warm air than 2 blade fan

Feature

Heat powered - no batteries or electricity required.
Efficiently circulates warm air throughout the room.
Less consumption, more efficiency.
Innovative and durable design.
Silent operation

Description

1.The fan base and blade are made from anodized aluminum which will not rust or corrode. This stove fan has been designed to deliver a very broad thermal current.
2.The stove fan generates its own power by the heat from the stove .
3.The strip of metal in the base of the fan is a Bi-metallic strip designed to raise the edge of the fan slightly as the maximum operating temperature is approached.
4.Operating above the recommended temperature of 660 F / 350 C may damage the fan and the electricity generating units.
5.Keep fan away from small children when in use.
Operation
: 1.Position the stove fan on a smooth flat surface of your stove top near the side or back of the stove.
2.The hotter the stove is, the more air the fan circulates.
3.The stove fan is designed for usage on freestanding stoves with a normal surface temperature of between 185 F - 660 F (85 C - 350 C).
4.Remove the fan from the stove if the temperature exceeds of 660 F / 350 C
5.Never handle the base of the stove fan, do not set the stove fan down on an unprotected surface when hot.
6.To move or carry the fan, always use the extendable handle while wearing gloves
7.Good stove safety practice includes the use of a stove thermometer.

2. 1800W ZVS Induction Heating Board Module Low Voltage High Frequency 12-48V Flyback Driver Heater with Tesla Coil and Cooling Fan

Feature

The induction heating boards maximum power is 1800W, adopted super PCB layout design and super heat sink, heat dissipation good, since with a cooling fan interface, can also do Tesla discharge, generator voltage inverter, etc
The induction heating circuit adopt 12-48V DC power supply, maximum current is 40A, the power uo to 1800W. It can work continuously under the condition of good heat dissipation. moderate power which make it can be used to quenching, annealing and other heat treatment. also for melted with graphite crucible kim/silver/ copper/aluminum and so on, heating is evenly and fast
it is recommended that not exceed 48V 35A to prevent accidents and damage,Although withstand more than 40A current.Induction heating is recommended to use 36V 20A power supply, 12V power supply is too small almost without response, and 12V power might lead to the voltage decreases, which is very dangerous.More than 24V/20A power supply, the greater the voltage/current, the greater the heating power, heating faster.
please check the power output meets the requirements if the MOS tube fever,and be sure to do a good job of cooling.Do not empty the board, otherwise it will create a very high noise, then MOS tube will burn out
please do not to heat too large metal, otherwise it may be overloaded, please add a 35A fuse or ammeter and air switch for better use (not included).

Description

Specification:
Product size:Approx.180x90x80mm (please allowed 1-3mm error)
Heater ring inner:70mm (Recommended crucible+quartz suit,maximum support of 58mm crucible)
Power supply:
New style :AC 100-220V Adapter
Old style: Main board Input voltage: 12V-48V recommend: 36V above
Power requirements: less than 12V10A , 15V above15A
NOTE:New style and Old style shipped by randomly!!!
It doesn't affect the performance of product.!!!
Maximum power: 1800W
Maximum current: 40A
Package Content:
1 x PCB board
1 x 48V copper tube

1.The power of heating is very large, except that the plate and components are hot, and the heat of copper tube is very high. you can buy a small water pump and 2 meters of rubber hose(inner diameter is 4mm) for build a water cooling system
Please pay attention to using switch power supply, because output voltage is slowly rising, and if the voltage rise to 10V before connected induction heating circuit that will be lead to circuit can't afford to vibrate caused by lacking voltage,so that the two MOS tube conduction and components will burned
comes with heating circle diameter-60 mm/design voltage-36V,if you use more than 40V Devices shall be used 70 mm diameter heating ring, DC 12V water pump use, please use separate power supply voltage regulator module to avoid fan and water pump are burn out
The minimum input is 12V, but it doesn't mean all 12V power supply available,The module has specific requirements on voltage and current , 12V require current must than 10A ,output power will greatly reduced if the power is too low ,which will lead to two MOS conduction at the same time & burn MOS tube when lower than 12V

3. Portable Space Heater 1500W/1100W with Oscillating Function Electric Heater Personal Fan with PTC Heating Body Induction Over-heat & Tip-over Protection for Indoor and Desk Office

Go to amazon.com

Feature

Fast Warm-Up & Energy-efficient: Adopting durable PTC ceramic heating element, Weird Tails Electric Heater has the advantages of 3 seconds fast heating, durability, no open flames and on oxygen consumption.
Overheat & Safety Protection: Automatic overheat system will shut the unit off when the parts of the heater overheat. The main body adopts premium VA66 fire-retardant plastic housing.
Warm & Natural Wind for All Year Use: Natural Wind mode provides comfortable natural wind ventilate your room nicely. not only as a heater but a normal electric fan, use its fan-only mode to generate refreshing air circulation without added heat for year-round convenience.
Low Noise & Oscillating Function: Low noise at 45 dB will not disturb your sleeping, reading, working and so on. The heater futures Auto Oscillating 90 degrees left and right keep the air flowing in every direction.
TWO YEARS SATISFACTION WARRANTY: TWO YEARS Warranty and full 30 DAYs money-back guarantee. Your purchase is fully protected and we back all our customer purchases. Just click "Add to Cart" worry-free with this guarantee and we hope that you will love our heater.

Description

Place the space heater under or on your desk/tabletop next to you to warm your numb fingers and frostbitten toes while working or watching TV

Technical Parameter:

Power Input: AC110V/60HZ

Heating Element: PTC Ceramic Heater

Product Weight: 1.2kg/ 2.65lbs

Product Dimensions: H21.5 * 13.5cm

Power Cord Length: 1.8m/ 5.9ft

4. Induction Innovations MD-700 Mini-Ductor II Magnetic Induction Heater Kit

Go to amazon.com

Feature

Releases thread lock compounded nuts, frozen manifold bolts, bearings and more
Completely hand-held, ergonomic, grenade style grip and a bright LED to illuminate work area
Works with all the mini-ductor coils and attachments
Operates on standard 110v/10 amp circuit
The MINI-DUCTOR II MD700 1,000W hand held induction power inverter
LED at terminal end provides for work area illumination
Grenade grip for better handling
Also great for hail dent removal

Description

Basic kit comes with: (1) Nutz-Off pre-formed coil, (1) bearing buddy (rope) coil, (1) U-form coil (23" insulated wire) and owners manual. This induction heater kit features a grenade grip for a greasy hand technician, work illuminating LED for increased vision of product application. It operates on 120 volts/1000 watts of power and is faster and safer than a torch. It uses high frequency magnetic fields to heat metal. The Mini-Ductor II allows you to heat and expand frozen, rusted, or thread-lock compound nuts without the collateral damage from a flame. Loosen seized hardware, bearings, gears, pulleys, lug nuts, in-line applications, fuel tank straps, PDR applications (paint-less dent repair), and more.

5. 1800W ZVS Induction Heater Induction Heating Board Module Tesla Coil 12-48V Low Voltage DC Power Supply with a Maximum Current of 40A, Flyback Driver Heater

Go to amazon.com

Feature

This Induction Heating Board Module has a maximum power of 1800W, super PCB layout design and super heat sink, superior heat dissipation effect
12-48V low voltage DC power supply with a maximum current of 40A. It can work continuously for several hours with good heat dissipation
Can use graphite crucible to melt gold, silver, copper, aluminum and other metals, heating evenly, fast and very convenient
With a cooling fan interface, can also do Tesla discharge, generator voltage inverter, etc
Flyback Driver Heater is recommended not to exceed 48V 35A to prevent accidents and damage

Description

Specification:
Input Voltage: 12V-48V (Recommendation: above 36V)
Power Requirments: Less than 12V >=10A, More than 15V >=15A
Maximum Power: 1800W
Maximum Current: 40A
Heater Inner Ring: 70mm / 2.8in
Size: 18 * 12 * 9 cm / 7.1 * 4.7 * 3.5in
Weight: Approx. 1052g

Package Included:
1 x PCB Board
1 x Copper Tube

Note:
1. When using a switching power supply, make sure that the power supply voltage is stable before connecting to the induction heating circuit.
2. Do not heat metal that is too large or it may be overloaded. Please add a 35A fuse or ammeter.
3. Although this driver board can withstand more than 40A, it is recommended not to exceed 48V 35A to prevent accidents and damage.
4. The minimum input voltage of the module is 12V, the voltage of 12V must be greater than 10A to use the power supply.
5. If you find that the MOS tube is hot, first consider whether the power output meets the requirements.
6. Do not clear the circuit board, otherwise it will emit a very high frequency of noise, and then the MOS tube will burn out.
7. It is recommended to use a 36V 20A power supply. Below 12V is very dangerous.

6. 1800W ZVS Induction Heating Board Module Flyback Driver Heater with Tesla Coil and Fan

Go to amazon.com

Feature

Max Power : 1800W
Input voltage: 12V-48V, recommend: 36V above
The ZVS low voltage induction heating board module adopted super PCB layout design and super heat sink, heat dissipation good, since with a cooling fan interface, can also do Tesla discharge, generator voltage inverter, etc..
The ZVS induction heater can be used by DIY players to give smaller players the parts can be treated by quenching, annealing and other heat treatment. You can also be melted with graphite crucible Kim, silver, copper, aluminum and other metal, heating evenly, is fast and very convenient.
In this test, the maximum power is close to 1600W, and the maximum current is 35A. This zvs flyback driver product is available at under the condition of good heat dissipation, the utility model can work continuously for hours.

Description

Note
1. The power of heating is very large, except that the plate and components are hot, and the heat of copper tube is very high. The buyer can prepare water cooling system separately, can buy a small water pump and 2 meters of inner diameter of 4mm rubber hose.
2. You must pay attention to when using switch power supply, because the high-power switching power supply usually have soft start function, namely the output voltage is slowly rising, and if the voltage rise to 10V before connected induction heating circuit will be caused by lacking voltage lead to circuit can't afford to vibrate, so that the two MOS tube conduction and burned components at the same time, so be sure to switch the power supply voltage stability and then access the induction heating circuit.
3. When heating the metal objects do not to heat too large metal, otherwise it may be overloaded with power, please add a 35A fuse or ammeter and air switch will be better. (package does NOT included)
4. Although this drive plate can withstand more than 40A current, but it is recommended that not exceed 48V 35A to prevent accidents and damage.
5. Package comes with heating circle diameter is 60 mm, design voltage is 36V, if you use more than 40 voltage power supply shall be used for inner diameter 70 mm above diameter heating ring, water pump use 12V dc power supply, please use separate power supply voltage regulator module to avoid burn out fan and water pump.

7. Wood Stove Heat Powered Fan

Go to amazon.com

Feature

SAVE MONEY ON ELECTRICITY! No electricity required. Works off the HEAT produced by your fireplace or wood-burning stove. The hotter the fire, the faster the blades turn. Therefore, more warm air gets dispersed throughout your house!
WHISPER-QUIET! 170-190 CFM Above 900 RPM and MAX Temperature of 644 F (340 C) The only moving part is the blade assembly. Say good-bye to the loud noise of electric forced-air fans! You won't even know this fan is there - but you'll FEEL the WARMTH!
MAINTENANCE-FREE! Just dust it off occasionally, and put some light oil on the blade shaft to keep it spinning smoothly and quietly!
"BUILT-IN" FIRE-STOKING INDICATOR! Because this fan operates on HEAT, you'll automatically know it's time to stoke the fire when the fan slows down! The higher the heat, the faster the blades spin. So when they're slowing down and you're not feeling the heat as much as before, it simply is telling you to stoke the fire! What could be easier?
SAFETY PLACEMENT OF FAN - Fan should be placed on the back of the stove (not in front) 6 inches away from the stove pipe

Description

No Need to Sit So Close to the Fire Anymore!

If you own a fireplace or wood burning stove and you would like to get MORE HEAT throughout your house but you DO NOT want to spend more money on electricity - all you have to do is get one of these amazing heat powered fireplace stove fans, and you will be warm and toasty for FREE!

That is because this fan does not use ANY electricity. Just set it in the right place, and the heat from your fireplace or stove will turn the fans and blow HOT AIR exactly where you want it! If you have a large room or large house to heat, you already know that a FAN is the best thing for getting the heat to be dispersed throughout your living space.

It does not even require maintenance - except for occasional dusting! Plus, the fan acts as an indicator that your fire needs to be stoked. When the spinning starts to slow down, you automatically know that it is time to stoke the fire with more wood!

No assembly required. Lasts forever. Makes a great winter housewarming gift!
10 YEARS LIMITED MANUFACTURE WARRANTY

8. CWLAKON Heat Powered Stove Fan-2020 Upgrade Designed Silent Operation 4 Blades with Stove Thermometer for Wood/Log Burner/Fireplace-Eco Friendly and Efficient Heat Distribution(Black)

Go to amazon.com

Feature

Start Automatically2018 Upgrade Technology,Reinforced 4 Blades,Faster Speed,Larger Air Volume.The heat powered stove fan is designed to circulate the warm air created by a wood / coal or pellet burning.Efficiently circulates warm air throughout the room.
Eco-Friendly and Self-PoweredThermoelectric module acts as a small generator to power the fan's motor. No batteries or electricity required! Improved warm air circulation results in greater comfort and reduce wood consumption from your stove.Stove operating with normal surface temperatures between 122F(50C) and 716F(380C).[Energy Class A+++]
Whisper QuietNewly Designed Blade,Larger Air Volume,Lower noise.You don't even know the stove fan is there,but you feel the warmth!You will enjoy the warm air in a quiet and comfortable environment.
Safty DesignThe stove fan support is made with Anodized Aluminum, able to resist high temperature up to 662F(350C), no deformation and no discoloration even after long time working under high temperature.
Longer LifetimeThere is a Bi-metallic safety device in the base of the fan.If the surface temperature rises above around 400F (200C),the safety device gently elevates the front of the fan to protect the TEG and motor.2-Year Warranty

Description

Box Contains:
1 x Heat powered stove fan
1 x Stove Thermometer

Specifications:
* Material: Anodized Aluminum
* Starting Temperature: 50C (122F)
* Max Working temperature: 350C (662F)
* AirFlow: 280-360CFM (cubic feet per minute)
* Noise: < 32dB
* Height: 190mm
* Width: 110mm
* Weight: 547g/800g(Inc. color box)
* Color: Black
* Running RPM:1350RPM
* Magnetic Stove Thermometer:Diameter 63mm,monitor temp from 70-900F(40-500C).(+/- 10%),placed on the stove top or side,or single wall pipe.

Heat Powered Stove Fan for Fireplace:
* The fans spins according to the heating temperature setting on the fireplace.
* Spreads heat out into the room instead of straight up to the top of the ceiling.
* Doesn't require electricity, heat driven, helps circulate warm air within the room from the corner and by the chimney into more of the room.
* Postion the fan on a smooth, flat area of the top of the stove. It will not fall off due to the stable base.
* Works on Wood, Gas or Pellet Stoves.
* Stands approximately 8.85" tall on top of the stove. This sleek design takes up very minimal space.
* This is the fan for you! Anyone with a wood stove needs this. No electric expense, runs for free, totally energy-saving and economical.

Maintenance-free:
Just dust it off occasionally, and put some light oil on the blade shaft to keep it spinning smoothly and quietly!

Warning:
Never handle the base of the stove fan, do not set the stove fan down on an unprotected surface when hot.
To move or carry the fan, always use the extendable handle while wearing gloves. Please keep fan away from small children when in use.

Click add to cart and buy the Best Heat Powered Stove Fan today.

9. Semoic 1800W ZVS Induction Heating Board Module Flyback Driver Heater+Tesla coil+fan

Go to amazon.com

Feature

Note: The power of heating is very large, except that the plate and components are hot, and the heat of copper tube is very high. The buyer can prepare water cooling system separately, can buy a small water pump and 2 meters of inner diameter of 4mm rubber hose.You must pay attention to when using switch power supply, because the high-power switching power supply usually have soft start function, namely the output voltage is slowly rising,
and if the voltage rise to 10V before connected induction heating circuit will be caused by lacking voltage lead to circuit can't afford to vibrate, so that the two MOS tube conduction and burned components at the same time, so be sure to switch the power supply voltage stability and then access the induction heating circuit.When heating the metal objects do not to heat too large metal, otherwise it may be overloaded with power, please add a 35A fuse or ammeter and air switch will be better.
(package does not inclues)Although this drive plate can withstand more than 40A current, but it is recommended that not exceed 48V 35A to prevent accidents and damage.Package comes with heating circle diameter is 60 mm, design voltage is 36V, if you use more than 40 voltage power supply shall be used for inner diameter 70 mm above diameter heating ring, water pump use 12V dc power supply, please use separate power supply voltage regulator module to avoid burn out fan and water pump.
The minimum input voltage of the module is 12V, it doesn't mean all the 12V power supply can be used, some novice buyers may use a smaller power supply. This module has specific voltage and current requirements, the voltage 12V current must be more than 10A power supply can be used, if the power is too low will lead to the power output is greatly reduced, when the voltage is lower than 12V, it will lead to two MOS at the same time conduction, will burn MOS tube;
If you find that the MOS tube fever, then the first thing to consider whether the power output meets the requirements.Do not empty the board, otherwise it will issue a very high frequency of noise, and then MOS tube will burn outInduction heating is recommended to use 36V 20A power supply, 12V power supply is too small heating almost no response, and 12V power supply easily lead to the power supply output voltage decreases, below 12V is very dangerous

Description

Semoica legal trade mark, has been registered. Only those who are authorized are available to sell items under Semoic. Semoic will bring you joyful shopping experience. 1800W ZVS Induction Heating Board Module Flyback Driver Heater+Tesla coil+fan
Note: Induction heating power is great, so fever is normal, be sure to do a good job of cooling.
Induction heating, the power recommended more than 48V 50A switching power supply. More than 24V power supply, then more than 20A power supply, the greater the voltage, the greater the current, the greater the heating power, heating faster.
This products maximum power 1800W, adopted super PCB layout design and super heat sink, heat dissipation good, since with a cooling fan interface, can also do Tesla discharge, generator voltage inverter, etc..
In this test, the maximum power is close to 1600W, and the maximum current is 35A. This product is available at under the condition of good heat dissipation, the utility model can work continuously for hours.
Name: ZVS Induction Heating Board Module
Model: 854337
Product size: 180mm x 90mm x 80mm
Heater ring inner: 70mm (Recommended crucible + quartz suit, maximum support of 58mm crucible)
Input voltage: 12V-48V recommend: 36V above
Power requirements: less than 12Vgreater than equal 10A , 15V above greater than equal 15A
Maximum power: 1800W
Maximum current: 40A
colour: black
Material: plastic + metal
Package Included
1 x PCB board
1 x 48V copper tube
Only the above package content, other products are not included.
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.

10. Lazmin ZVS Heating Board Module, 1800W 40A ZVS Induction Heating Board Module Heater DIY Flyback Driver Heater+Tesla Coil+Fan

Go to amazon.com

Feature

This product has a maximum power of 1800W, super PCB layout design and super heat sink, superior heat dissipation effect
12-48V low voltage DC power supply with a maximum current of 40A. It can work continuously for several hours with good heat dissipation
Can use graphite crucible to melt gold, silver, copper, aluminum and other metals, heating evenly, fast and very convenient
With a cooling fan interface, can also do Tesla discharge, generator voltage inverter, etc
It is recommended not to exceed 48V 35A to prevent accidents and damage

Description

Specification:
Input Voltage: 12V-48V (Recommendation: above 36V)
Power Requirments: Less than 12V >=10A, More than 15V >=15A
Maximum Power: 1800W
Maximum Current: 40A
Heater Inner Ring: 70mm / 2.8in
Size: 18 * 12 * 9 cm / 7.1 * 4.7 * 3.5in
Weight: Approx. 1052g

Package Included:
1 x PCB Board
1 x Copper Tube

Note:
1. When using a switching power supply, make sure that the power supply voltage is stable before connecting to the induction heating circuit.
2. Do not heat metal that is too large or it may be overloaded. Please add a 35A fuse or ammeter.
3. Although this driver board can withstand more than 40A, it is recommended not to exceed 48V 35A to prevent accidents and damage.
4. The minimum input voltage of the module is 12V, the voltage of 12V must be greater than 10A to use the power supply.
5. If you find that the MOS tube is hot, first consider whether the power output meets the requirements.
6. Do not clear the circuit board, otherwise it will emit a very high frequency of noise, and then the MOS tube will burn out.
7. It is recommended to use a 36V 20A power supply. Below 12V is very dangerous.

Conclusion

By our suggestions above, we hope that you can found the best induction heater with fan for you. Please don't forget to share your experience by comment in this post. Thank you!