There are many reasons you might choose to buy xt60 distribution board but it is not easy to find the best suitable xt60 distribution board for you. But don’t worry! We did some of the work for you already by researching a few models on the current market. Let’s check following article to find the best xt60 distribution board.
Best xt60 distribution board
Related posts:
Best xt60 distribution board reviews
1. FPVDrone Matek PDB XT60 Power Distribution Board BEC-5V/2A 12V/0.5A with XT60 Plug for Quadcopter
Feature
BEC 5V output:Designed for RC Receivers, Flight controllers, OSD, and Servos;BEC 12V output:Designed for Video TX or FPV camera with linear regulatorInput voltage range from 9 - 18V DC (3S-4S LiPo operation)
The Matek PDB has been engineered to provide the highest possible performance and reliability in a 36*50mm & 4 layers PCB
With a Amass XT60 plug, easy to connect with LiPo pack;4-layer PCB Board, high current power and BEC stratification, avoid ground disturbance BEC power current
The mounting hole size is M3,suit for CC3D naze32 F4 F3 flight controller,can be used for the standard CC3D F3 F4 F7 Naze32 Fligh Controller
Description
Description:General:
-Input voltage range (3S-4S LiPo operation): 9 - 18V DC
-Regulated 5V and 12V outputs
-LED power indicators ( 5V & 12V outputs )
-6 ESC outputs & 1 pair VCC/GND pads
ESC outputs:
-Continuous current: 25A*4 or 15A*6
-Peak current (10 seconds/minute): 30A*4 or 20A*6
BEC 5V output:
-Designed for RC Receivers, Flight controllers, OSD, and Servos.
-DC/DC synchronous buck regulator.
-Voltage: 5.0 +/- 0.1VDC
-Continuous current: 2 Amps (Max.2.5A 10s/minute)
-Output Ripple: 40mV (VIn=16V, VOut=5V@2A load)
-Short-circuit tolerant (5 seconds/minute)
BEC 12V output:
-Designed for Video TX or FPV camera with linear regulator.
-The battery should be 4S LiPo (13~18V DC)
- Voltage: 12.0 +/- 0.3VDC
-Continuous current: 500mA (Max.0.8A 5s/minute)
-Short-circuit tolerant (2 seconds/minute)
BEC 12V @ 3S LiPo
-Output voltage= 3S LiPo voltage -1V
Physical:
-Dimensions: 36 x 50 x 4 mm (without XT60)
-Mounting: 30.5 x 30.5mm, 3mm
- Weight: 7.5g(w/o XT60), 11g(w/ XT60)
Features:
2oz copper, 4-layers &1.6mm PCB.
Built-in XT60 Socket
Total 6 pairs ESC solder tabs are fit for H or X type frame 5V & 12V Output LED
indicators & Short circuit tolerant
Package included:
1 x Matek Power Distribution Board
2. PDB Power Distribution Board (Matek Systems) + 4pcs Sponge Mat Landing Pad Gear (XT60 PDB (3-4S))
Feature
Support 3S-4S Battery (9-18V) ------ Batteris may range from 3S -4S ( 3S 4S Lipo Battery ),some customer said 2S is also available, while we do not recommend that,some of device may not work because of power.Suitable for standard CC3D F3 Naze32 F4 F7 Flight Controller ------- Suitable for M3 standoff or screw .The size is 36*36mm,mounting holes 30.5mm square spacing suitable, can be used for the standard CC3D F3 F4 F7 Naze32 Fligh Controller (Standard size is also 36*36mm,mounting holes 30.5mm spuare spacing)
Used for most FPV Racing Drone ------ with 30.5*30.5mm (hole to hole) size, the PDB can are a standard size for 180 sized quads drone & up, such as 190 200 210 220 230 250 Racing Drone
4 * 20A ESC Output (25A Max), BEC 5V 12V Output ----- 20A continuous current per output, 25A PEAK CURRENT (10 seconds/minute) per output.------ providing synchronized & regulated DC 5V outputs & linear regulated DC 12V for powering camera, servos , RC Receiver , Flight Controller , Video Transmitter , LED , etc
4PCS Sponge Mat Landing Pad Gear is suitable for most drone ------ Great for mini quads from 180mm to 300mm in size, great replacement pads for quadcopters like QAV210 QAV250 QAV-R 180 220 260 Martain II and so on.
Description
Specifications:General:
- Input voltage range (3S-4S operation): 9 - 18VDC
- Regulated 5V and 12V outputs
- LED power indicators ( 5V & 12V outputs )
- 4 ESC outputs
ESC outputs:
- Continuous current: 20A per output
- Peak current (10 seconds/minute): 25A per output
BEC 5V output:
- Designed for RC Receivers, Flight controllers, OSD, and Servos.
- DC/DC synchronous buck regulator, Efficiency is up to 95%.
- Voltage: 5.0 +/- 0.1VDC
- Continuous current: 3 Amps
- Short-circuit tolerant (10 seconds/minute) - LED (indicates voltage is in regulation)
BEC 12V output:
- The battery should be 4SLiPo
- Standard output designed to power cameras and video transmitters,etc.
- Voltage: 12.0 +/- 0.2VDC
- Continuous current: 2 Amps (Max.3A 10s/minute)
- Short-circuit tolerant (10 seconds/minute)
- LED (indicates voltage is in regulation)
About the FPV Sponge Mat Landing Skid Pad Gear:
1. Super light, strengthen shockproof,anti-static.
2 .Great for mini quads from 180mm to 300mm in size, great replacement pads for quadcopters like QAV210 QAV250 QAV-R 180 220 260
Package:
1 * PDB
1 * Manual
4 * Sponge Mat Landing Pad Gear
3. AKK NO.1 PDB Power Distribution Board with ESC Output BEC 5V & 12V Output for FPV Multirotor Quadcopter
Feature
5V & 12V Output LED indicators & Short circuit tolerantSolder Bridges of various voltage for Camera & VTX.
ESC & Battery solder pads in pairs, It convenient solder bridge of various voltage for camera & VTX.
DC outputs for powering cameras, servos, VTX, LEDs, etc. Batteries may range from 3S to 6S LiPo.
This PDB distributes power from a battery pack to 4 ESCs, as well as providing synchronised & regulated.
Description
Features
ESC & Battery solder pads in pairs
Solder Bridges of various voltage for Camera & VTX.
5V & 12V Output LED indicators & Short circuit tolerant
Specifications
General:
- Input voltage range (3S-6S operation): 9 - 26VDC
- Regulated 5V and 12V outputs
- LED power indicators ( 5V & 12V outputs )
- 4 ESC outputs
ESC outputs:
- Continuous current: 20A per output
- Peak current (10 seconds/minute): 25A per output
BEC 5V output:
- Designed for RC Receivers, Flight controllers, OSD,
and Servos.
- Voltage: 5.0 +/- 0.2VDC
- Continuous current: 3 Amps
- Short-circuit tolerant (10 seconds/minute)
- LED (indicates voltage is in regulation)
BEC 12V output:
- The battery should be 4S~6S LiPo
- Standard output designed to power cameras
and VTX,etc.
- Voltage: 12.0 +/- 0.2VDC
- Continuous current: 2 Amps (Max.3A 10s/minute)
- Short-circuit tolerant (10 seconds/minute)
- LED (indicates voltage is in regulation)
CAM & VTX voltage bridge
- 3S operation. choose "VCC"for 12V camera & 12V VTX,
VCC=Battery Voltage.
- 4~6S operation, choose "12" for 12V camera & 12V VTX
- 3~6S operation, choose "5"for 5V camera
- Video pass through from the "CAM"pad to the "VTX"pad
Physical:
-Dimensions: 36 x 36mm
-Weight: 6g
-Mounting holes: 30.5mm
4. usongs New Quadcopter Power Distribution Board XT60 XT-60 20a Quad Mutlicopter 2mm Lite
Feature
Features. . Current: 4 x 20A Outputs (MAX) . Power Input: XT60 with 16AWG wire . Motor output: 4 x 20mm Female bullet plug . Aux output: 2 pin JST compatible . Weight: 19.3g (including wires) .Description
New Quadcopter Power Distribution Board XT60 XT-60 20a Quad Mutlicopter 2mm Lite5. Yiqigou Power Distribution Board PDB XT60 with BEC 5V and 12V 2oz Copper for RC Helicopter Quadcopter
Feature
Input Voltage Range(3S-4S Lipo operation): DC 9-18V; Regulated 5V and 12V outputs; LED power indicators( 5V & 12V outputs); 6 ESC outputs & 1 pair VCC/GND pads.ESC outputs:Continuous current: 25A*4 or 15A*6;Peak current (10 seconds/minute): 30A*4 or 20A*6.
BEC 5V output:Designed for RC Receivers, Flight controllers, OSD, and Servos; DC/DC synchronous buck regulator; Voltage: 5.0 +/- 0.1VDC; Continuous current: 2 Amps (Max.2.5A 10s/minute); Output Ripple: 40mV (VIn=16V, VOut=5V@2A load); Short-circuit tolerant (5 seconds/minute) .
BEC 12V output:Designed for Video TX or FPV camera with linear regulator; The battery should be 4S LiPo (13~18V DC);Voltage: 12.0 +/- 0.3VDC; Continuous current: 500mA (Max.0.8A 5s/minute); Short-circuit tolerant (2 seconds/minute).
BEC 12V @ 3S LiPo;Output voltage= 3S LiPo voltage -1V.
Description
Production Description:
General:
Input Voltage Range(3S-4S Lipo operation): DC 9-18V.
Regulated 5V and 12V outputs.
LED power indicators( 5V & 12V outputs).
6 ESC outputs & 1 pair VCC/GND pads
ESC outputs:
Continuous current: 25A*4 or 15A*6
Peak current (10 seconds/minute): 30A*4 or 20A*6
BEC 5V output:
Designed for RC Receivers, Flight controllers, OSD, and Servos.
DC/DC synchronous buck regulator.
Voltage: 5.0 +/- 0.1VDC
Continuous current: 2 Amps (Max.2.5A 10s/minute)
Output Ripple: 40mV (VIn=16V, VOut=5V@2A load)
Short-circuit tolerant (5 seconds/minute)
BEC 12V output:
Designed for Video TX or FPV camera with linear regulator.
The battery should be 4S LiPo (13~18V DC)
Voltage: 12.0 +/- 0.3VDC
Continuous current: 500mA (Max.0.8A 5s/minute)
Short-circuit tolerant (2 seconds/minute)
BEC 12V @ 3S LiPo
Output voltage= 3S LiPo voltage -1V
Package Include:
1 * Matek XT60 PDB for RC Helicopter Quadcopter
6. REALACC RX130 130mm FPV Racing Drone Frame 3mm 3K Carbon Fiber Unibody with 5V/12V Power Distribution Board XT60
Feature
Fits standard 30.5x30.5mm mounting boardsIncludes 5V/12V power distribution board and XT60 connector
3mm pure carbon fiber unibody main frame
Description
Specifications:Wheelbase: 130mm
Arm thickness: 3mm
Main board: 2mm
Weight: 70g
Recommend parts ( Not included)
130mm Frame kit
Motor: 1306-1407 Motor
Propeller: 3020 propeller
ESC: 6-20A
Flight Control: CC3D/Naze32/F3/F4 Flight Controller
Battery: 2S / 3S 450-800mAh Battery
Package Includes:
1 X X130 Frame kit
1 X 5V/12V Power Distribution Board
1 X XT60 plug
7. USAQ F3 Naze32 PDB Power Distribution Board with Video Signal LC Filter 5V 12V UBEC
Feature
Includes 5V and 12V power supply for video equipmentLC filter integrated for decreased interference in video and FPV signal
Description
Description:Item Name: PCB with Filter BEC
BEC Outpur: 5V 12V
Input Voltage: 2-6S
MAX.: 3A
Dimension: 36*36mm
Mounting Distance: 30.5mm
Weight : 6g
Features:
Latest UBEC, LC Filter
Integrated filter circuit boards, more stable,make FPV further and clearer
Compatible with CC3D/Naze32/F3 flight controller
Package Includes:
1 x PDB
8. Hobbypower Shock Absorber Integrated Power Hub PDB Power Distribution Board BEC 12V for APM2.6 APM2.8 Pixhawk PX4 Flight Controller
Feature
Distribution panel, current and voltage sensors, 5VBEC, 12VBEC, damping plate, 5 in 1, copper thickens, over current can reach 90a, and integrates the current and voltage sensors and support 3S-6S input current.suitable for APM, PIX and others, also with 12V and 5VBEC, BEC increased the level of LC filtering, greatly reducing the power output of the ripple, 12V and 5V output is more pure, 12V and 5V support 3A current
integrated into the damping plate, a multi use, can let your aircraft to reduce unnecessary wiring and power module plug can be in line the public version of the APM2.5/2.6/2.8 and PIXHAWK flight control
Description
Features:Distribution panel, current and voltage sensors, 5VBEC, 12VBEC, damping plate, 5 in 1, copper thickens, over current can reach 90a, and integrates the current and voltage sensors and support 3S-6S input current.
Voltage is suitable for APM, PIX and others, also with 12V and 5VBEC, BEC increased the level of LC filtering, greatly reducing the power output of the ripple, 12V and 5V output is more pure, 12V and 5V support 3A current.
New ideas, using black heavy gold PCB board, the APM power module and ESC distribution board are integrated into the damping plate, a multi use, can let your aircraft to reduce unnecessary wiring and power module plug can be in line the public version of the APM2.5/2.6/2.8 and PIXHAWK flight control
Specifications:
Size: 90 x 60 x 8mm/3.5 x 2.4 x 0.3 inch
Delivery size: 150 x 128mm/5.9 x 5 inch
Net weight: 34g
Package weight: 37g
Package included:
1 x Shock Absorber
1 x cable
3 x stickers
1 x manual
9. Matek Systems PDB-XT60 W/ BEC 5V & 12V 2oz Copper for RC Drone FPV Racing Multi Rotor
Feature
2oz copper, 4-layers &1.6mm PCBBuilt-in XT60 Socket
Total 6 pairs ESC solder tabs are fit for H or X type frame 5V & 12V Output LED indicators & Short circuit tolerant
Input voltage range (3S-4S LiPo operation): 9 - 18V DC
LED power indicators ( 5V & 12V outputs )
Description
The PDB-XT60 has been engineered to provide the highest possible performance and reliability in a 36*50mm & 4 layers PCB. It distributes power from a LiPo pack to 6 ESCs, as well as providing synchronised & regulated DC 5V outputs & linear regulated DC 12V for powering Cameras, Servos, RC receiver, Flight Controllers, Video Transmitters, LEDs, etc. It offers a XT60 socket to connect the LiPo pack conveniently.Description:
General:
-Input voltage range (3S-4S LiPo operation): 9 - 18V DC
-Regulated 5V and 12V outputs
-LED power indicators ( 5V & 12V outputs )
-6 ESC outputs & 1 pair VCC/GND pads
ESC outputs:
-Continuous current: 25A*4 or 15A*6
-Peak current (10 seconds/minute): 30A*4 or 20A*6
BEC 5V output:
-Designed for RC Receivers, Flight controllers, OSD, and Servos.
-DC/DC synchronous buck regulator.
-Voltage: 5.0 +/- 0.1VDC
-Continuous current: 2 Amps (Max.2.5A 10s/minute)
-Output Ripple: 40mV (VIn=16V, VOut=5V@2A load)
-Short-circuit tolerant (5 seconds/minute)
BEC 12V output:
-Designed for Video TX or FPV camera with linear regulator.
-The battery should be 4S LiPo (13~18V DC)
- Voltage: 12.0 +/- 0.3VDC
-Continuous current: 500mA (Max.0.8A 5s/minute)
-Short-circuit tolerant (2 seconds/minute)
BEC 12V @ 3S LiPo
-Output voltage= 3S LiPo voltage -1V
Physical:
-Dimensions: 36 x 50 x 4 mm (without XT60)
-Mounting: 30.5 x 30.5mm, 3mm
- Weight: 7.5g(w/o XT60), 11g(w/ XT60)
10. CigouMatek Systems PDB XT60 W/BEC 5V & 12V 2oz Copper for RC Helicopter Quadcopter
Feature
2oz copper, 4-layers &1.6mm PCBBuilt-in XT60 Socket
Total 6 pairs ESC solder tabs are fit for H or X type frame
5V & 12V Output LED indicators & Short circuit tolerant
Input voltage range (3S-4S LiPo operation): 9 - 18V DC Regulated 5V and 12V outputs
Package included:
1 x Matek Systems PDB-XT60
Description
=^_^= Hi, Dear Friend, Welcome to Cigou, Have a Great Shopping Time. =^_^=Specifications
LED power indicators ( 5V/12V outputs )
6 ESC outputs & 1 pair VCC/GND pads
ESC outputs:
Continuous current: 25A*4 or 15A*6
Peak current (10 seconds/minute): 30A*4 or 20A*6
BEC 5V output:
Designed for RC Receivers, Flight controllers, OSD, and Servos.
DC/DC synchronous buck regulator.
Voltage: 5.0 +/- 0.1VDC
Continuous current: 2 Amps (Max.2.5A 10s/minute)
Output Ripple: 40mV (VIn=16V, VOut=5V/2A load)
Short-circuit tolerant (5 seconds/minute)
BEC 12V output:
Designed for Video TX or FPV camera with linear regulator.
The battery should be 4S LiPo (13~18V DC)
Voltage: 12.0 +/- 0.3VDC
Continuous current: 500mA (Max.0.8A 5s/minute)
Short-circuit tolerant (2 seconds/minute)
BEC 12V/3S LiPo
Output voltage= 3S LiPo voltage -1V
Dimensions: 36 x 50 x 4 mm (without XT60)
Mounting: 30.5 x 30.5mm, 3mm
Weight: 7.5g(w/o XT60), 11g(w/ XT60)
About review:
If you have any dissatisfaction with your item, please email us before you leaving any 1 or 2 ratings, negative feedback.Your satisfactory is always our Priority, We will do our best to resolve the issues.
If you receive damaged items or your item have anything wrong, please be free to contact us , we will try our best to solve it.