Looking for a ramps shield? Have a look at this 2020 guide!

It took days of going through more than a thousand customer reviews and conducting expert researches to narrow down the list. Weve included a comparison table below to give you a quick summary of our top 10 ramps shield. Its followed by an in-depth review of each ramps shield. Hopefully, once you are done reading this article, you will be well informed about ramps shield and be able to select the right ramps shield for you without any hesitations.

Best ramps shield

Related posts:

Best ramps shield reviews

1. HiLetgo RAMPS 1.4 Control Panel 3D Printer Control Board Reprap Control Board Support Arduino Mega 2560

Feature

The fifth stepper motor output port can be customized as a Z-axis motor or a second extruder.
Can be extended to control other accessories.
Three field effect transistors, three heater / fan output ports, three thermistor circuits.
Heated bed control, extra 11A fuse.
Pololu board foot socket, can be easily replaced or removed.

Description

Description:
RepRap Mega Pololu Shield, or RAMPS for short. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.

Features
1.It has Cartesian robots and regulations of the extruder .
2.Extended to control other accessories.
3.Heater / MOSFET outputs and three fan thermistor circuit.
4.Integration of additional security 5A and component protection.
5.Control of additional heating bed 11A fuse.
6.Suitable for 5 Pololu stepper driver board.
7.Pololu board pin socket, so they can be easily replaced or removed for future designs.
8.I2C and SPI pins left for future expansion.
9.Hooked into all MOSFET PWM pin versatility.
10.Servo type connector is used to connect to the end stop , the motor and the light-emitting diodes. These connectors are gold-plated , rated current of 3A, very compact.
11.On the SD card to add - is now available from the Kliment - Sdramps.
12.LED indicate when the heater output.
13.Option 2 motors connected to Z Prusa Mendel.

Package Included
1* RAMPS 1.4 Control Panel 3D Printer Control Board Reprap Control Board

2. WOWOONE CNC 3D Printer Kit for Arduino Mega 2560 R3 RAMPS 1.4 Controller LCD 2004 + 6X Limit Switch Endstop 5 A4988 Stepper Driver 3D Printerarduino arduino

Feature

3D Printer Accessories Set meets most needs. Including CNC Shield V3.0, UNO R3 Board, A4988 StepStick Stepper Motor Module.
The 3D printer stepper motor shield V3 can be used as driver expansion board for engraving machines and 3D printers.
It has in total 4 channel slots for A4988 stepper motor driver modules for driving 4 channel of stepper motors.
Each channel of stepper motor only needs 2 IO ports, which means 8 IO ports is sufficient to manage 3 stepper motors
This shield can make quick work for managing stepper motors in your project

Description

CNC Shield Board:
1>PWM Spindle and direction pins
2>4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
3>2 x End stops for each axis (6 in total)
4>Coolant enable
5>Uses removable A4988 or DRV8825 compatible stepper drivers
6>Compact design
7>Stepper Motors can be connected with 4 pin molex connectors or soldered in place
8>Please note that this is an unassembled kit and Basic soldering skills are needed
A4988 Stepper Motor Driver:
1>Low RDS (On) Output
2>Automatic current decay mode detection / selection
3>Mix with slow current decay modes
4>Synchronous rectification for low power dissipation
5>Internal UVLO
6>Crossover-current protection
7>3.3 and 5 V compatible logic supply
8>Thermal shutdown circuitry
9>Ground fault protection
10>Load short-circuit protection
11>Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16
UNO R3 Board for Arduino:
1>MCU: ATmega328
2>USB interface: ATmega16U2
3>Operating voltage: 5V
4>Digital I/O pins: 14 (including 6 with PWM capability)
5>Analog input pins: 6
6>I-I/O pin output current: 40mA max
7>3.3V output current: 150mA max
8>Flash memory: 32kB (0.5kB used by bootloader- included)
9>Static RAM (SRAM): 2kB
10>EEPROM: 1kB
11>Clock speed: 16MHz
LCD 2004 Smart Controller
Easy connect it to your Ramps board using the "smart adapter" included.
After connecting this panel to your Ramps you don't need your pc any more, the Smart Controller supplies power for your SD card.
Further more actions like calibration, axes movements can be done by adjusting the rotary encoder on the Smart Control panel.

3. Aokin 3D Printer Controller Kit for Arduino RepRap, RAMPS 1.4 + Mega 2560 Board + 5pcs A4988 Stepper Motor Driver with Heatsink + LCD 12864 Graphic Smart Display with Adapter

Feature

Mega 2560 control board: The board is a microcontroller board based on the ATmega2560-16AU .It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
RAMPS 1.4: RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
LCD 12864 with Controller: This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the "smart adapter" included.
A4988 driver module: A4988 Stepper Motor Driver Board is a breakout board for Allegros A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection; please read the A4988 datasheet carefullybefore using this product.
Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered isasking for trouble.)

Description

Product Specs:

(1) Mega 2560 R3
(2) 3D Printer Controller RAMPS 1.4 It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino-compatible Mega with the powerful Arduino-compatible MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion.
(3) A4988 Stepper Motor Driver
A4988 is a complete microstepping motor driver with built-in translator for easy operation
(4) LCD 12864 Graphic Smart Display Controller
This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the "smart adapter" included.
Update High Quality Ramp Board by changing MOSFET: old MOSFET IC Model : PDF55N06 SpecificationVDSS:60V ID:55A New MOSFET IC model: HM60N06 SpecificationVDSS:60V ID:60A HM60N06 current up to 60AMore safety

Package List:

(1) RAMPS 1.4 x 1
(2) Mega 2560 R3 x 1
(3) A4988 Stepper Motor Driver with Heatsink x 5
(4) LCD 12864 Graphic Smart Display Controller x 1
(5) Smart Adapter x 1
(6) Cable x 2
(7) USB Cable x 1

Detailed tutorials including project introduction and source code CAN BE PROVIDED FOR FREE,contact us BY Email to get documents.

Note:
1. You just need to connect the computer with Mega 2560 via USB download cable when burning firmware.
2.The chip and circuit may be burnt when the power and motor driver board reversed, so please confirm twice before powering.
3.You just need to power Ramps 1.4 when testing.If you power Mega 2560, the chip will be burnt easily. So please read the introduction carefully and avoid the board being burnt due to the wrong operation.

4. WINGONEER 3D Printer Controller RAMPS 1.4 Mega Shield for Arduino Reprap Prusa Mendel

Feature

Fully assembled & tested, no soldering required
It is designed to fit the entire electronics needed for a RepRap in one small package for low The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion
A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack
It has Cartesian robots and requirements of the extruder

Description

WINGONEER trademark Reg.NO:4747611

WINGONEER 3D Printer Controller RAMPS 1.4 Mega Shield for Arduino Reprap Prusa Mendel

Description:
Specification:
Heater / fan output and three thermistors MOSFET circuits;
Fusion 5A additional safety and component protection;
Extra bed heating control fuse 11A;
Suitable for 5 Pololu stepper driver board;
Pololu board pin socket, easy to be replaced and removed;
I2C and SPI pin for extended use; All MOSFET into PWM pins for versatility;
Rated current: 3A; LED indicates when the heater output;
Option 2 motors connected to the Z Prusa Mendel
Package Size: 12.2cm x 6.8cm x 3.2cm
Package Weight:72g

Package Includes:
1 x 3D Printer Controller for RAMPS 1.4

5. 3D Printer RAMPS 1.4 Controller + MEGA2560 R3 + A4988 With Heat Sink USB Calbe Jumper Kit

Feature

The RAMPS 1.4 board is designed to fit the entire electronics needed for a RepRap in one small package for low cost
RAMPS interfaces an Mega with the powerful MEGA platform and has plenty room for expansion
The modular design includes plug in stepper drivers and extruder control electronics on an MEGA shield for easy service, part replacement, upgrade-ability and expansion
Additionally, a number of expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack
With the boot-loader, download the program directly via USB without having to go through other external writer

Description

Specifications:

RAMPS 1.4 Size: 9.1 x 5.9cm / 3.58 x 2.32"

Mega R3 2560 Size: 10.8 x 5.5cm / 4.25 x 2.16"

A4988 Quantity: 5pcs

Package Includes:

1 x RAMPS 1.4 Board
1 x Mega 2560 R3 Board
5 x Soldered A4988 Drivers
5 x Heat Sinks
1 x USB Cable
19 x Jumpers

6. 3D Printer CNC Controller Kit with for ArduinoIDE, Longruner GRBL CNC Shield Board+RAMPS 1.4 Mechanical Switch Endstop DRV8825 A4988 Stepper Motor Driver Nema 17 Stepper Motor LKB02

Feature

Latest CH340G CNC Shield expansion board Version 3.0 for Arduino.
Longruner UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2 with 1.5m USB Cable.
4pcs DRV8825 Stepper Motor Driver with Heat Sinks.
3pcs NEMA-17 Stepper Motor 84 oz.in (59 Ncm) 47mm Body 1.8 degree with Mounting Bracket Kit DIY 3D Printer CNC Robot with 3pcs Mounting Bracket and 12pcs M3 Screws.
3pcs Endstop Mechanical Limit Switches for 3D printer RAMPS 1.4 with 3Pin 70cm Cable.

Description

CNC Shield Board:
Latest CNC Shield Version 3.0 for arduino.
GRBL 0.9 compatible.
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13).
2 x End stops for each axis (6 in total).
Coolant enable.
Compatible with A4988 or DRV8825 stepper driver.
Runs on 12-36V DC.

DRV8825 Stepper Motor Driver:
Stepper motor driver (upgraded from A4988, 2.5 A max current/phase. It's not arduino official board but it's compatible with all arduino software and hardware).

Nema 17 Stepper motor Specification:
Model No.:17HD48002H-22B
Step Angle: 1.8 deg
Holding Torque: 59Ncm(84 oz.in)
Rated Current/phase: 1.7A
Frame Size: 41 x 41mm
Body Length: 47mm
Shaft Diameter: 5mm
Shaft Length: 22mm
Weight: 380g

Mechanical Endstop Connection Description:
Red line connect VCC (ramps of +)
black wire connect the GND (ramps of -)
Green Line connect SIGNAL (ramps in s)
Tips: Under normal circumstances, the system must be configured to at least three mechanical switches.
Advantage: Easy to install, the more common used styles.
Length of Cable: 70 cm

Great Package Includes:
1 x CNC Shield Board
1 x Longruner UNO R3 Board
1 x 1.5m USB cable for R3 Board
3 x Nema 17 stepper motor 1.7 A (with bracket and screw)
3 x Nema 17 Stepper Motor Mounting Bracket
3 x Mechanical Switch Endstop
3 x 3Pin 70cm Cable
4 x DRV8825 Stepper Motor Driver
4 x Aluminum heatsink w/ 3M tape backing
12x M3 Screws for bracket of stepper motor

7. [Sintron] 3D Printer Controller RAMPS 1.4 Arduino Mega Pololu Shield for Reprap Prusa Mendel Arduino Mega2560

Feature

(1) 3 mosfets for heater / fan outputs and 3 thermistor circuits.
(2) Pololu boards are on pin header sockets so they can be replaced easily or removed for use in future designs.
(3) All the Mosfets are hooked into PWM pins for versatility.
(4) Servo style connectors are used to connect to the endstops, motors, and leds. These connectors are gold plated, rated for 3A, very compact, and globally available.
(5) Fused at 5A for additional safety and component protection , Heated bed control with additional 11A fuse .

Description

Overview

The RepRap Arduino-compatible MEGA Pololu Shield, or RAMPS for short. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino-compatible Mega with the powerful Arduino-compatible MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.

Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.


Features

(1) It has provisions for the cartesian robot and extruder.
(2) Expandable to control other accessories.
(3) 3 mosfets for heater / fan outputs and 3 thermistor circuits.
(4) Fused at 5A for additional safety and component protection .
(5) Heated bed control with additional 11A fuse .
(6) Fits 5 Pololu stepper driver board .
(7) Pololu boards are on pin header sockets so they can be replaced easily or removed for use in future designs.
(8) I2C and SPI pins left available for future expansion.
(9) All the Mosfets are hooked into PWM pins for versatility.
(10) Servo style connectors are used to connect to the endstops, motors, and leds. These connectors are gold plated, rated for 3A, very compact, and globally available.
(11) USB type B receptacle .
(12) SD Card add on available .
(13) LEDs indicate when heater outputs on .
(14) Option to connect 2 motors to Z for Prusa Mendel .

8. Caliber CA0212 Ramp Shield Adapter Kit-Triton Double Axle and SnoPro V-Front, Black

Feature

Universal design fits most open trailers
LowPro GripGlides are installed on the ramp to make unloading your snowmobile and ATV simple
Molded grips down the center to give your snowmobile track traction
Lightweight HDPE not to crack, chip, break or wear out

Description

The Caliber V-Front Ramp Shield with LowPro GripGlides protect your snowmobiles, ATVs and motorcycles from road grime, rocks and salt when hauling. The universal fit works with most V-front open trailers. The shield stands at an aerodynamic 30" height to help with gas mileage, and comes with LowPro GripGlides to make unloading your snowmobile and ATV simple. Lightweight HDPE not to crack, chip, break or wear out. Stainless steel hardware is included.

9. 3D Printer CNC Kit, TopDirect Professional CNC Module Kit for Arduino GRBL CNC Shield + UNO R3 Board + RAMPS 1.4 Mechanical Switch Endstop + DRV8825 Stepper Motor Driver + Nema 17 Stepper Motor

Feature

Latest CH340G CNC Shield expansion board Version 3.0 for Arduino, and compatible for GRBL 0.9.
UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2 with 1.5m USB cable.
5pcs RAMPS 1.4 Mechanical Switch Endstop for 3D printer RAMPS 1.4 with 3pin 70cm cable.
5pcs DRV8825 Stepper Motor Driver with heat sink, upgraded from A4988, max. current: 2.5A, 32 subdivision: 1, 1/2, 1/4, 1/8, 1/16, 1/32.
3pcs Nema 17 Stepper Motor 59 Ncm (84 oz.in) 47mm Body 1.8 degree with mounting bracket kit.

Description

This is a professional sensor kit for UNO R3. New and upgraded, we provides various components or sensor module, with which you will find it easy for you to complete every experiments or learning. All these are packaged in a portable case, easy to carry and storage.

CNC Shield Board:
Latest CNC Shield Version 3.0 for Arduino
GRBL 0.9 compatible
4-Axis support (X, Y, Z, A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis
Coolant enable
Compatible with A4988 or DRV8825 stepper driver
Working Voltage: 12-36V DC
Max. Working Current: 2.5A

RAMPS 1.4 Mechanical Switch Endstop:
Red: VCC (ramps +)
Black: GND (ramps -)
Green: SIGNAL (ramps s)

DRV8825 Stepper Motor Driver:
Size: 1.5mm x 2mm
Upgraded from A4988
Maximum Current: 2.5A
32 Subdivision: 1, 1/2, 1/4, 1/8, 1/16, 1/32
4-layer PCB board for better heat dissipation
Suitable for driving stepper motors up to 8.2V~45V, 2.5A

Nema 17 Stepper Motor:
Model: 17HD48002H-22B
Rated Current/phase: 1.7A
Step Angle: 1.8 deg.
Holding Torque: 59Ncm(84 oz.in)
Frame Size: 41 x 41mm
Body Length: 47mm
Shaft Diameter: 5mm
Shaft Length: 22mm

Package Lists:
1 x CNC Shield V3
1 x UNO R3 MEGA328P CH340G with USB Cable
5 x DRV8825 Stepper Motor Driver with Heat Sink
5 x RAMPS 1.4 Mechanical Switch Endstop
5 x 3pin Cable (70cm)
3 x Nema 17 Stepper Motor
3 x Nema 17 Mounting Bracket

10. KEYESTUDIO 3D Printer Controller RAMPS 1.4 REPRAP MENDEL PRUSA for Arduino Mega

Feature

It is a Mega Pololu Shield, or RAMPS for short, designed to fit the entire electronics needed for a RepRap in one small package for low cost.
RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion.
Has provisions for the cartesian robot and extruder.
Expandable to control other accessories.
3 mosfets for heater / fan outputs and 3 thermistor circuits.

Description

Introduction
It is a Mega Pololu Shield, or RAMPS for short, designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful
Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy
service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top
of the stack.
Specification
1. Has provisions for the cartesian robot and extruder;
2. Expandable to control other accessories;
3. 3 mosfets for heater / fan outputs and 3 thermistor circuits;
4. Fused at 5A for additional safety and component protection;
5. Heated bed control with additional 11A fuse;
6. Fits 5 Pololu stepper driver board;
7. Pololu boards are on pin header sockets so they can be replaced easily or removed for use in future designs;
8. I2C and SPI pins left available for future expansion;
9. All the Mosfets are hooked into PWM pins for versatility;
10. Servo style connectors are used to connect to the endstops, motors, and LEDs. These connectors are gold plated, rated for 3A, very compact;
11. SD Card add on available
12. LEDs indicate when heater outputs on
13. Option to connect 2 motors to Z for Prusa Mendel

Conclusion

By our suggestions above, we hope that you can found the best ramps shield for you. Please don't forget to share your experience by comment in this post. Thank you!