All in all, we spent hundreds of hours combing through thousands of user reviews to put together a comprehensive list of the best induction heating power supply module on the market. We then delved into these induction heating power supply module further and put together detailed reviews so that you can easily pick the best induction heating power supply module for your needs.
Best induction heating power supply module
Related posts:
Best induction heating power supply module reviews
1. 1800W ZVS Induction Heating Board Module Flyback Driver Heater with Tesla Coil and Fan
Feature
Max Power : 1800WInput voltage: 12V-48V, recommend: 36V above
The ZVS low voltage induction heating board module adopted super PCB layout design and super heat sink, heat dissipation good, since with a cooling fan interface, can also do Tesla discharge, generator voltage inverter, etc..
The ZVS induction heater can be used by DIY players to give smaller players the parts can be treated by quenching, annealing and other heat treatment. You can also be melted with graphite crucible Kim, silver, copper, aluminum and other metal, heating evenly, is fast and very convenient.
In this test, the maximum power is close to 1600W, and the maximum current is 35A. This zvs flyback driver product is available at under the condition of good heat dissipation, the utility model can work continuously for hours.
Description
Note1. The power of heating is very large, except that the plate and components are hot, and the heat of copper tube is very high. The buyer can prepare water cooling system separately, can buy a small water pump and 2 meters of inner diameter of 4mm rubber hose.
2. You must pay attention to when using switch power supply, because the high-power switching power supply usually have soft start function, namely the output voltage is slowly rising, and if the voltage rise to 10V before connected induction heating circuit will be caused by lacking voltage lead to circuit can't afford to vibrate, so that the two MOS tube conduction and burned components at the same time, so be sure to switch the power supply voltage stability and then access the induction heating circuit.
3. When heating the metal objects do not to heat too large metal, otherwise it may be overloaded with power, please add a 35A fuse or ammeter and air switch will be better. (package does NOT included)
4. Although this drive plate can withstand more than 40A current, but it is recommended that not exceed 48V 35A to prevent accidents and damage.
5. Package comes with heating circle diameter is 60 mm, design voltage is 36V, if you use more than 40 voltage power supply shall be used for inner diameter 70 mm above diameter heating ring, water pump use 12V dc power supply, please use separate power supply voltage regulator module to avoid burn out fan and water pump.
2. ZVS Driver Module,5V-12V ZVS Low Voltage Induction Heating Power Supply Board+Heating Coil
Feature
ZVS heating power supply module including 1pcs heating coilInput voltage- DC 5V-12V; Max Power-120W (when 12V induction heating)
Ensure all the components welding right,power line connect in right way,than to set up an electric circuit
Width of the heated object : as far as possible 1/3~1/2 , maximum inner diameter of the heating coil: not more than 2/3
PCB size: 55 mmx37 mmx1.6 mm
Description
Specification:
Input voltage: DC 5v-12 v
Maximum power 120w (12 v induction heating). 12 v, push the ignition coil primary 5 + 5 turn, about 30 w.
PCB size: 55 mmx37 mmx1.6 mm
Heating coil, the width of the heated objects as far as possible between the heating coil diameter of 1/3 ~ 1/2, most not more than two-thirds.
Package Included:
1 x ZVS driver board
1 x heating coil
3. LeaningTech 5V~12V Zero Voltage Switching ZVS Induction Heating Power Supply Module + Coil Power Supply heating power supply module
Feature
ZVS heating power supply module including heating coilInput voltage DC5V-12V(We are not guarantee the module will work when the voltage is over 12V or less than 5V)
Maximum power 120W(when 12V eddy-current heating)
Ensure all the components welding right, power line connect in right way, than to set up an electric circuit.
The width of the heated object is as far as possible between the 1/3~1/2 of the inner diameter of the heating coil, the maximum not more than 2/3!
Description
Specification: Input voltage: 5v-12v Module dimensions:5.542 cm(LWH) Product Weight: 119g Coil size: length:7.5cm width: 2.8cm Features: ZVS heating power supply module including heating coil Input voltage DC5V-12V(We are not guarantee the module will work when the voltage is over 12V or less than 5V) Maximum power 120W(when 12V eddy-current heating) Ensure all the components welding right,power line connect in right way,than to set up an electric circuit. The width of the heated object is as far as possible between the 1/3~1/2 of the inner diameter of the heating coil, the maximum not more than 2/3! Package Included: 1 pc ZVS heating power supply module 1 pc heating coil4. Ximimark 1PCS for ZVS Induction Heating Power Supply Module Tesla Jacob's Ladder 5V-12V 9V 120W
Feature
the product is for ZVS heating power supply module, does not include the heating coilthe input voltage DC 5 v to 12 v
heating coil, the width of the heated objects as far as possible between the heating coil diameter of 1/3 ~ 1/2, most don't more than two-thirds.
Package Include: 1 x5 v ~ 12 v for ZVS induction heating power supply module tesla Jacob's ladder
If You Are Not Satisfied with Your Purchase for Any Reason, Please Feel Free To Contact Us at the Buyer Center or Support Email, 24/7 Quick Reply.
Description
Description:
Note:the product is for ZVS heating power supply module, doesnot includethe heating coil
1, this no tap mini plate for ZVS finished board, with no heating coil, ignition coil and a cooling fan, etc
2, the input voltage DC 5 v to 12 v
3, maximum power 120 w (12 v induction heating). 12 v, push the ignition coil primary 5 + 5 turn, about 30 w.
4, PCB size: 55 mm * 37 mm * 1.6 mm
5, heating coil, the width of the heated objects as far as possible between the heating coil diameter of 1/3 ~ 1/2, most don't more than two-thirds.
6, induction heating, power work five minutes to cool. For induction heating current is larger, heating coil is relatively large. When heated, part of the heat generated by the heated object will be passed on to the heating coil, over time, the temperature of the heating coil will be high. If the heating coil in the words of the terminal, the terminal part of plastic melt!!!! Therefore, induction heating the best heating coil directly welded to the PCB. This buyer, please note
PackageInclude:
1 x5 v ~ 12 v for ZVS induction heating power supply module tesla Jacob's ladder
5. Fdit 5V-12V ZVS Low Voltage Induction Heating Power Supply Module with Coil
Feature
ZVS heating power supply module including heating coilInput voltage DC5V-12V (We do not guarantee the module will work when the voltage is over 12V or less than 5V). We suggest the voltage is 5V to 12V, or the overload current or voltage lead to the smoked module
Maximum power 120W (when 12V eddy - current heating)
Ensure all the components welding right, power line connect in right way, than to set up an electric circuit.
The width of the heated object is as far as possible between the 1/3 ~ 1/2 of the inner diameter of the heating coil, the maximum not more than 2/3!
Description
Description:Note: the product is ZVS heating power supply module, include the heating coil.
1, this no tap mini plate ZVS finished board, with no ignition coil and a cooling fan, etc.
2, the input voltage DC 5 v to 12 v.
3, maximum power 120 w (12 v induction heating). 12 v, push the ignition coil primary 5 + 5 turn, about 30 w.
4, PCB size: 55 mm * 37 mm * 1.6 mm.
5, heating coil, the width of the heated objects as far as possible between the heating coil diameter of 1/3 ~ 1/2, most don't more than two-thirds.
6, induction heating, power work five minutes to cool. For induction heating current is larger, heating coil is relatively large. When heated, part of the heat generated by the heated object will be passed on to the heating coil, over time, the temperature of the heating coil will be high. If the heating coil in the words of the terminal, the terminal part of plastic melt!!!! Therefore, induction heating the best heating coil directly welded to the PCB.
package include:
1 x ZVS heating power supply module
1 x heating coil
6. fosa 1800W Induction Heating Module ZVS Low Voltage 12V-48V Induction Heating Board Flyback Driver Heater DIY High Frequency Induction Heating Machine Module
Feature
This product has a maximum power of 1800W, super PCB layout design and super heat sink, superior heat dissipation effect12-48V low voltage DC power supply with a maximum current of 40A. It can work continuously for several hours with good heat dissipation
Can use graphite crucible to melt gold, silver, copper, aluminum and other metals, heating evenly, fast and very convenient
With a cooling fan interface, can also do Tesla discharge, generator voltage inverter, etc
It is recommended not to exceed 48V 35A to prevent accidents and damage
Description
Specification:Input Voltage: 12V-48V (Recommendation: above 36V)
Power Requirments: Less than 12V >=10A, More than 15V >=15A
Maximum Power: 1800W
Maximum Current: 40A
Heater Inner Ring: 70mm / 2.8in
Size: 18 * 12 * 9 cm / 7.1 * 4.7 * 3.5in
Weight: Approx. 1052g
Package Included:
1 x PCB Board
1 x Copper Tube
Note:
1. When using a switching power supply, make sure that the power supply voltage is stable before connecting to the induction heating circuit.
2. Do not heat metal that is too large or it may be overloaded. Please add a 35A fuse or ammeter.
3. Although this driver board can withstand more than 40A, it is recommended not to exceed 48V 35A to prevent accidents and damage.
4. The minimum input voltage of the module is 12V, the voltage of 12V must be greater than 10A to use the power supply.
5. If you find that the MOS tube is hot, first consider whether the power output meets the requirements.
6. Do not clear the circuit board, otherwise it will emit a very high frequency of noise, and then the MOS tube will burn out.
7. It is recommended to use a 36V 20A power supply. Below 12V is very dangerous.
7. JullyCAnnice Professional ZVS Low Voltage Induction Heating Power Supply Module 5V-12V 120W Induction Heating board With Coil
Feature
🦄 ZVS, Low Voltage, Induction, Heating Power Supply Module, 5V-12V🦄 One of best heating power supply module.
🦄 The product Package Included: heating coil.
🦄 Input voltage DC5V-12V(We are not guarantee the module will work when the voltage is over 12V or less than 5V).
🦄 Maximum power 120W(when 12V eddy-current heating).
Description
Features:One of best heating power supply module.
The product Package Included: heating coil.
Input voltage DC5V-12V(We are not guarantee the module will work when the voltage is over 12V or less than 5V).
Maximum power 120W(when 12V eddy-current heating).
Ensure all the components welding right, power line connect in right way,than to set up an electric circuit.
Descriptions:
The width of the heated object is as far as possible between the 1/3~1/2 of the inner diameter of the heating coil, the maximum not more than 2/3.
Specifications:
Input voltage: 5v-12v
Module dimensions: 5.5*4*2 cm
Coil size: length:7.5cm
width: 2.8cm
Color: black
Package Included:
1 x Heating Power Supply Module
Notes:
The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness.
8. Akozon DC12-30V 20A 1000W ZVS Power Supply Driver Board Induction Heating Module Heater
Feature
The driver module is made of high standard 1.6mm double layer fiberglass board for durabilityFactory customized large inductance coil is winded with 1.2mm copper wire for more stable performance and consistent parameter
This ZVS driver module uses 5-band resistors for small error and stable performance
More tin is added on the board bottom so the driver board can be used for induction heating without burning out
Use 12-30V DC power and current is more than 10A. The higher the voltage, the longer the arc (tested with 27V/15A power supply and it can generate 80mm long arc). As a induction heating board, the higher the voltage, the faster and hotter heating will be
Description
Description:
This ZVS board uses high quality 1.6mm double layer fiberglass board, large inductance coil and stable 5-band resistors that ensures its stable performance. With a proper power supply and correct circuit, you can create a beautiful electric arc by yourself. This is a popular board and you can buy one for yourself or give one to your electronics hobbyist friend as a gift.
Specifications:
Voltage: DC12V-30V
Max. Current: 20A
Max. Power: 1000W
Size: 69 x 85 x 30mm / 2.71 x 3.34 x 11.81"
Quantity: 1
Package Includes:
1 x ZVS Board
9. 1000W 20A ZVS Low Voltage Induction Heating Board Module Tesla with Coil 12V-48V Flyback Driver Heater DIY
Feature
12-48V low voltage power supply. Maximum current 20A, Maximum power 1000W.The bigger voltage, the higher power.Tested 53V power supply when working properly. It can be used for DIY players to make small parts quenching, annealing and other heat treatment, heating fast, very convenient
This circuit can do induction heating, or replace copper tube with high frequency transformer, it will be a powerful inverter
The higher voltage, the higher current when heating the same things, the effect is better, but at the same time heating is also higher, therefore the choice of input voltage is based on your need.24V or 36V power supply is enough
Note: buyer need to bring their own power and cooling unit
Description
Features:
24V input with no load current of 3A , 48V input with no load current of 6A
buyer need self-provided power and water cooling device
This circuit can do induction heating, or replace copper tube with high frequency transformer, it will be a powerful inverter
Note:
The kit contains a full set of driving circuit elements and brass
Buyers need to bring their own power and cooling unit.
The circuit board using double-sided fiberglass board, mainly copper traces are used to widen use the entire back surface of the resonant circuit common, continuous work, please add a fan to blow down from above, to the resonance capacitors and other components cool.
The use of switching power supply Please note that due to high power are generally slow start function, which just opened machine output voltage is slowly rising, while it is turned on before the induction heating circuit if the voltage rises to 12V, because start insufficient voltage can not afford to vibration, resulting in two simultaneous conduction mos tube so burned components.
So the first will start switching power supply voltage reaches 12V above and then access the induction heating circuit.
The volume of the object being heated inside the heating coil can not exceed 1/5 of the volume (if the heating cylinder, then heating coil diameter less than the diameter of 1/3), or it may be due to overload or burn out the power supply to the circuit.
Although this circuit can tolerate 20-30A input current moment, but do not exceed 15A when safe work, you can easily add an ammeter between the power supply and heating driver board but always monitor the current overload
Package Includes:
1 x 20A 1000W Flyback driver inductive heater Zero Voltage Switching Tesla
1 x Coil
10. fosa 2000W Induction Heating Module ZVS High Voltage 24V-70V Induction Heating Board Flyback Driver Heater DIY High Frequency Induction Heating Machine Module
Feature
Temperature protection: Heatsink temperature higher than 65 C, enter protection. under 65 C back to normal.Undervoltage protection: Input voltage is less than 20V, enter protection. Input voltage up to 24V back to normal.
Power tube broken/short circuit, display MOS-XX. Only iron can be heated directly. Other metal materials need graphite crucible.
Copper pipe and water pipe connections, the need to seal to prevent water leakage.
Please installed the copper coil and water pump, then connect the power supply.(can not empty load)
Description
Specification:Size: about 198*100*95mm/7.8*3.94*3.74in
Copper tube coil: 50mm
Input voltage: DC 24V-70V
Input current: 48A (Max), Power: 2000W
Short Circuit/Overload: Input current is greater than 40A, voltage greater than 55V, enter protection.
Package List:
1 * Induction Heating Board
1 * Spiral Copper Pipe
1 * Water Pipe
1 * Mini Water Pump
1 * Adapter
1 * US Plug
1 * Screw Package
1 * Telescopic Belt
Note:
1. This Induction Heater need 2000W power supply to Heating material.(Recommend 48-53V power supply
2. Only iron can be heated directly. Other metal materials need graphite crucible.
