10 best smd dd1 and cc1 for 2021

All in all, we spent hundreds of hours combing through thousands of user reviews to put together a comprehensive list of the best smd dd1 and cc1 on the market. We then delved into these smd dd1 and cc1 further and put together detailed reviews so that you can easily pick the best smd dd1 and cc1 for your needs.

Best smd dd1 and cc1

Related posts:

Best smd dd1 and cc1 reviews

1. Steave Meade Designs SMD DD-1 Distortion Detector

Feature

Distortion detector/analyzer (dd1)
Distortion detector's circuitry is 100% analog
Distortion detection trigger level > 1.0% harmonic distortion
Operating range of input signal is 1.2 vrms a" 125 vrms, (15, 000 watts at 1 ohm)
Signal present LED trigger voltage 750 mvrms

2. SMD Crossover Calibrator CC-1

Feature

The Crossover Calibrators circuitry is digital microprocessor controlled
Crossover -3dB point accuracy +/- 0.25dB
Low Battery LED trigger battery voltage < 6.5Vdc
Auto-shut off timer 8 - 10 minutes after ON button is pressed

3. SMD Distortion Detector & Crossover Calibrator Combo Pack

Feature

The Distortion Detectors circuitry is 100% analog, Distortion Detection trigger level > 1.0% Harmonic Distortion, Guaranteed operating range of input signal is 1.2Vrms 125Vrms. (15,000 Watts at 1 ohm) Autoranging
Signal Present LED trigger voltage 750mVrms, Low Battery LED trigger battery voltage < 5.6Vdc, Auto-shut off timer 8 - 10 minutes after ON button is pressed
The Crossover Calibrators circuitry is digital microprocessor controlled, Crossover -3dB point accuracy +/- 0.25dB, Low Battery LED trigger battery voltage < 6.5Vdc, Auto-shut off timer 8 - 10 minutes after ON button is pressed
The purpose of this tool is to enable the installer to set the gain of an audio amplifier to match the source units output level, accurately and quickly. It can also be useful for detecting distortion in the audio signal caused by poorly designed or malfunctioning audio equipment.
If you are in installer, Own a shop, Or a DIY car audio person and don't own these tools you are missing out on high end tuning capability. Not only can you tune the amps correctly but you can tune it in a way that lets you get the most out of your amps without damaging the amps and or your subs! SMD tools are a must have in our shop thats for sure!

4. SMD SunFlash UV Activated Polyester Resin (1 Gallon)

Feature

Works directly out of the container
100% UV Activated (Sets as fast as 1 minute in the sun!) - No lingering odor once fully cured
Zero catalyst required (Never mix too hot, or too cold; always perfect)
Almost zero waste (NO MORE "STUCK" BRUSHES!) - Excellent saturation
Work inside the shop and it never sets up until you bring it into the sunshine! (or UV Black Light (385-410nm)

5. SMD Audio Multi Meter/Hand Held Amplifier Dyno - Real time wattage tester

Feature

DC Voltmeter: -100 Volts to +100 Volts
AC Voltmeter: 0 - 150 VRMS / AC Ammeter: 0 - 100 ARMS
AC Apparent Power: 0 - 15,000 / VA Power Factor: 50 - 100%
Frequency: 10 - 20,000 Hz / AC Impedance: 0 - 200 Ohms
Real time wattage / True Power Dyno: 0 - 15,000 Watts

6. Steve Meade Designs SMD DD-1 Distortion Detector

Feature

Distortion detector/analyzer (dd1)
Distortion detector's circuitry is 100% analog
Distortion detection trigger level > 1.0% harmonic distortion
Operating range of input signal is 1.2 vrms a" 125 vrms, (15, 000 watts at 1 ohm)
Signal present LED trigger voltage 750 mvrms

7. Steve Meade Designs SMD CC-1 Crossover Calibrator

Feature

The Crossover Calibrators circuitry is digital microprocessor controlled
Crossover -3dB point accuracy +/- 0.25dB
Low Battery LED trigger battery voltage < 6.5Vdc
Auto-shut off timer 8 - 10 minutes after ON button is pressed

8. Steve Meade Designs SMD DD-1+ Distortion Detector Plus

Feature

The distortion detection circuitry is 100% analog, digital micro-processing system used for display and calculation of overlap
Distortion Detection trigger level > 1.0% Harmonic Distortion
3 stage autoranging for wide range of input signal from 1Vrms 200Vrms. (40,000 Watts at 1 ohm)
Auto-shut off timer 8 - 10 minutes after ON button is pressed
Battery self-test and display of condition when DD-1+ is initialized

9. Steve Meade Designs SMD DD-1+ and CC-1 Combo Pack

Feature

The distortion detection circuitry is 100% analog, digital microprocessing system used for display and calculation of overlap
Distortion Detection trigger level > 1.0% Harmonic Distortion
3 stage autoranging for wide range of input signal from 1Vrms 200Vrms. (40,000 Watts at 1 ohm)
The Crossover Calibrators circuitry is digital microprocessor controlled
Crossover -3dB point accuracy +/- 0.25dB

10. SMD QR-1 Quick Release Speaker Box Terminal

Feature

Comes with wire 10ga, but can take 8ga!
1/2" Aluminum or Copper terminal blocks w/ 5/16" x 18 set screws (fits up to 8ga wire)
CUT OUT DIAMETER - 2.75"
FLANGE DIAMETER - 3.80"
N52 Neodymium Magnets. VERY strong.

Conclusion

By our suggestions above, we hope that you can found the best smd dd1 and cc1 for you. Please don't forget to share your experience by comment in this post. Thank you!