Best brushless tiny whoop for 2020

What are criterias of the best brushless tiny whoop? It is not easy to find the answer. We spent many hours to analyst top 10 brushless tiny whoop and find the best one for you. Let’s find more detail below.

Best brushless tiny whoop

Related posts:

Best brushless tiny whoop reviews

1. BETAFPV Toothpick F4 2-4S AIO Brushless Flight Controller BLHELI_S 12A ESC No RX with XT30 Cable for Brushless Toothpick Carbon Fiber Racing Drone Like HX100 FPV Quadcopter(Pins Pre-soldered)

Feature

Toothpick F4 2-4S AIO 12A FCIntegrated with a Betaflight MATEKF411 processor FC, Betaflight OSD and 2-4S 12A ESC. Customized for Toothpick drone like HX100 HX115 FPV Quad. Supports 4S battery for fast-flying experience
Double-sided Motor Solder PadTwo options for motor installation which include pins connected or wire connected. FC is equipped with pins pad and wires pad, which offer you available choice to plug motor with pluggable pins or solder motor with wires. You will receive the pins connected version by default
New LayoutAll solder pads of this Toothpick F4 AIO FC are at the edge, with side-mount USB port, which is convenient for installation and solder
Real HolesComes with real holes instead of notches, customized for Toothpick carbon fiber drone, which is fitting for hole position to protect the carbon fiber kit for easy installation
Supported ReceiverThe F4 2-4S AIO FC Brushless Flight Controller builted without internal receiver, but supports external Frsky XM/XM+ Receiver/ DSMX Receiver / Futaba Receiver/ Flysky Receiver/ TBS Crossfire Receiver. Compatible receivers signal include PWM, Oneshot125, Oneshot42, Dshot150, Dshot300, Dshot600

Description

BETAFPV Toothpick F4 2-4S AIO Brushless Flight Controller BLHELI_S 12A ESC No RX OSD Smart Audio with XT30 Cable for Brushless Toothpick Carbon Fiber Racing Drone like HX100 FPV Quadcopter(Pins-connected Version)

SPECIFICATIONS OF ESC
Support BLheli/BLHELI_S suite Pass-through ready
Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Input voltage: 2S-4S Lipo
Continue current: 12A
Peak current: 15A
Firmware: BLHELI_S
Processor: SILABS EFM8BB21F16G-C
Motor Connectors: 1.25mm header pins connector
Factory firmware: G-H-30-16.7

Recommend Parts
Motors:
2S: 1103 11000KV Motor - www.amazon.com/dp/B07FN64599
3S: 1103 8000KV Motor - www.amazon.com/dp/B07SFJ1V6D
1105 6000KV Motor - www.amazon.com/dp/B07MZ2BSDT
4S: 1105 5000KV Motor - www.amazon.com/dp/B07SFHZSVT
Battery:
3S: 300mAh 3S Battery - www.amazon.com/dp/B07WH1VRP1
450mAh 3S - www.amazon.com/dp/B07QMR9KKL
4S: 450mAh 4S Battery - www.amazon.com/dp/B07RZ6PQPH
Frame:
HX100 Frame: www.amazon.com/dp/B07VFPFBRT

Package:
1 * F4 2-4S AIO 12A Toothpick Brushless FC with motor pluggable pins
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration rubber dampers

2. EMAX Tinyhawk Brushless Micro Indoor Racing Drone Whoop 75mm BNF FRSKY Ready to Fly FPV Beginners Durable Inverted Motors Full Acro Level Horizon Mode

Feature

Micro style drone 75mm, Lightweight and great for beginners.
FRSKY D8 receiver. (ONLY COMPATIBLE WITH FRSKY.)
Speeds up to 35mph.
Safe and Great for indoor racing
F4 processor and ultra fast Gyro system

Description

**DO NOT ATTEMPT TO CONNECT A 2s BATTERY! THIS QUAD IS 1s BATTERY ONLY!**
Product includes:
1 x Tinhawk Racing Drone
1 x Carrying Case
1 x 450mah 1s 4.35v HV Battery
1 x Bag of spare parts that include
1 battery connector and motor screws
1 x USB Battery charger with x 4 connectors, this allows you to charge 4 batteries simultaneously at 4.35V.
1 x Manual

FRSKY D8
Drone weight: 29grams
Weight with battery: 42grams with 450mAh 1S battery
Frame Material: polypropylene
Propeller: 40mm diameter
Blades: 3
Pitch: 23mm
Weight: 0.5g
Motor: long life bearings and beeper
Stator: 8mm x 2.5mm ( 08025 )
KV: 15000KV
Flight Controller: F4MATEKF411 firmware
ESCs: 4 in 1 3A
Receiver: EMAX Tiny receiver ( Compatible with Frsky D8 mode )
VTX Power: 25mW
Channels: 37CH
Camera: 600TVL CMOS
Battery: 1S 4.35V 450mAh LiHV
Discharge rating: 80C / 160C

Dismantling any conventional thinking, EMAX went back to the drawing board and created something new to reach all of its design goals with no compromise. The Tinyhawk offers incredible performance, thanks to a powerful F4 processor and ultra fast Gyro system, creating the most stable flight experience ever in a miniature racing drone the size of the palm of your hand. By creating an entirely new power system from the ground up, EMAX has achieved the perfect power to weight ratio, utilizing a lightweight micro brushless motor paired together with a state-of-the-art radical propeller design matched to the performance curve of the entire system.

Integrated into the Tinyhawk is a video transmission system with a first-person-view camera, allowing the pilot to utilize a compatible Virtual Reality goggle or screen to experience a pilot's view firsthand.

3. ARRIS Poke Micro FPV Mini RC Quadcopter Drone Micro Video Camera Drone UFO RTF w/ 5.8G 25mw AIO Camera Headless Mode One Key Return

Feature

This ARRIS poke micro drone is based on Eachine E010, better than other tiny whoop in the market.
One-key Return: With built-in positioning system, the drone can auto locate the remote control, just press the one key return button, the drone will fly back to the remote control's location.
FPV Camera: Equipped with 5.8G 25mW HD camera bringing a new perspective to your photos and videos from the air. All you need is the FPV goggle or FPV monitor.
This micro video camera drone has upgraded with ARRIS 25C 200mAh battery,up to 4min and 50 seconds flying time.
RTF version with a battery inside the package.

Description

Search this ASIN on amazon to buy extra batteries: B075L4MZJC

ARRIS Poke mini fpv quadcopter is one simplied and durable FPV quad for any level players. With the small size and light weight, you can fly it indoor or outdoors. This mini quad has many functions, you can fly it up/down,left/right, sideward flight, hovering, 3D-flip and etc. Press one-key return button, the quad will fly back to the remote controller's location. With the bright LED, you can enjoy the night flying.

Main Features:
High/low speed switch, suitable for indoor and outdoor.
Modular Design: FC,motor and Video tx camera connected through quick release terminal, no soldering needed, convenient for future upgrade and maintainance
Easy to fly: headless mode and one key return makes it suitable for any level of players
Good for FPV: It comes with high quality camera, which performs well in both bright and dark condition. The video tx is 5.8G 25mw 48 channel, suitable for most of the related fpv goggles and monitors.
Headless Mode: Usually, the forward direction of a flying multi-rotor is the same as the nose direction. By using Headless, the forward direction has nothing to do with nose direction. This lessens the steepness of the learning curve

Specifications:
Function: Forward/backward, up/down, left/right, sideward flight, hovering, 3D-flip, headless mode, high/low speed, one-key return, LED lights
Control distance: About 30m
Wheelbase: 65mm
Video TX: 5.8Ghz 25mw 48 CH with camera
Battery for quadcopter: 3.7V 200mAh 25C li-po battery
Flying time: About 4.5 minutes
Battery for remote controller: 2 * AA battery (not included)
Item dimension: 83 x 83 x 58mm
Item weight: 25g(battery included)

Package Included:
1 x ARRIS Poke FPV Mini Quadcopter RTF
1 x 3.7V 200mAh 25C Li-Po Battery
1 x USB Charging Cable
4 x Spare Propellers
1 x Manual

4. EMAX Tinyhawk S 1-2s Brushless Micro Indoor Racing Drone Whoop 75mm BNF FRSKY Ready to Fly FPV Beginners Durable Inverted Motors Full Acro Level Horizon Mode

Feature

Tinyhawk 1-2s capable.
55+MPH top speed
Includes 1 x 1s and 1 x 2s battery
Bigger motors than Tinyhawk Original plus it includes 4 blade propellers for Turtle Mode
Includes 1s and 2s battery charger

Description

***PLEASE READ BEFORE FLYING!***

*It takes 1s and 2s.

**To fly on 1s you will need to change PID and RATE profile from OSD to PID PROF 1 and RATE PROF 1.**

**To fly on 2s, you will need to change PID and RATE profile from OSD to PID Prof 2 and RATE PROF 2**

**To charge 2s batteries with USB connector, you will need to connect the BALANCE LEAD only.**

**To charge 1s batteries you will need to connect the PH2 PIN connector.**

***To access OSD, Left Joystick to left, and right joystick UP at the same time.***

*What's included:

1 x Tinyhawk
1 x set of quad blade propellers
1 x USB charger for 1s and 2s batteries.
1 x 300mah 2 battery
1 x 450mah 1s Battery
1 x Manual
1 x Bag spare parts
The Tinyhawk encapsulated the technological advancements made within the micro drone field, designed to fully realize the potential performance of a drone the size of the palm of your hand. But the engineers at EMAX didn't stop there. With further advancements pushing the boundaries within this miniature scale, the Tinyhawk S was born.
* Determined to increase the efficiency of the entire power system, the Tinyhawk S features a newly engineered brushless motor that is both smaller in scale in order to reduce weight, but also be able to spin at higher RPMs, increasing the power output of the entire aircraft.


* Utilizing this new power system, up to 20% more flight time than the previous generation can be achieved, as well as the ability to accept a higher voltage in order for the pilot to customize the performance of the Tinyhawk S. Featuring a dual slot mount, the camera will be able to adjust its angle to the pilot's preference to help navigate the craft at higher speeds. With newly reinforced struts, the frame's durability is unmatched in its class.

* The Tinyhawk S is the micro indoor racing drone.

5. BETAFPV F4 FC 1S Brushed Flight Controller with SPI Frsky Receiver OSD Smart Audio for FPV Tiny Whoop Micro Racing Drone

Feature

The world's first compatible BetaFlight OSD, FrSky Rx, BetaFlight firmware, born for acro flight controller for the Micro Whoop or Blade Inductrix quadcopter.
Fully programmable through Betaflight, using the onboard USB port, tune all the parameters, PID's, and rates to your perfect settings.
Built in SPI Frsky D8 protocol native receiver, compatible with almost ALL Frsky radios(e.g. Taranis X9D/X9D Plus/X7) or Frsky compatible transmitter module.
Designed to work with current Tiny Whoop or Blade Inductrix setups.
The flight controller board comes pre-flashed with Betaflight firmware, and pre-soldered 55mm power cable pigtail with JST-PH 2.0 connector, AKA PowerWhoop connector.

Description

BETAFPV F4 Brushed Flight Controller Integrated with OSD and Frsky Receiver for Tiny Whoop Drone.
BETAFPV F4 brushed FC board bring a new era in FPV whoop technology. STM32F411 100MHz high performance MCU, 30A lower resistance MOSFETs, SPI Frsky Rx, Build-in Betaflight OSD and polar reversed protection. All of these is backed by the same reliability and warranty of all BETAFPV FC boards.

Specifications:
CPU: STM32F411CEU6
Six-Axis: MPU6000
ESC: All FETs are rated at 30A maximum. Support 6x15mm/7x20mm/8x20mm/8.5x20mm etc motors.
Size: 26mm x 26mm,fully compatible with the Inductrix quad frame and mounting pattern
Firmware version: Betaflight MATEKF411RX 3.4.0
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Receiver: SPI Frsky D8 protocol (AKA FRSKY_D on Betaflight Configuration)
Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
Weight: 3.7g

Tips:
How would do an OSD with the AIO cameras?
There is a video in and out on the fc itself, labeled CAM and VTX as show below. There should be a video in and out on the AIO camera, like BETAFPV H02 etc. If not, you would have to modify the camera for sure but it would totally be worth it. There is some examples:
BETAFPV H02 or other AIO cameras with video in and out available.
FX806 or other AIO cameras with camera and vtx are connected with cables.
Other regular AIO cameras like VM275, FX805, Eachine XT02 etc.

BETAFPV Support Freshdesk for BetaFlight OSD Setup:
https://betafpv.freshdesk.com/support/solutions/articles/27000038661-betaflight-osd-setup

Package:
1 * F4 OSD brushed flight controller ( 55mm PH-JST 2.0 power cable soldered)
4 * M1.2x4mm screws (Fit for stock Inductrix frame)
4 * M1.4x5mm screws (Fit for Beta75 etc 75mm frame)
4 * Anti-vibration ruber dampers

6. 4pcs 0802 19000KV Brushless Motors 1S SE0802 Micro Drone Motor for Eachine UZ65 Snapper7 Micro FPV Racing Drone

Feature

Specification: 0802 motor shaft 1.0mm, weight 1.9g/pc, compatible with 1S lipo battery, suit for 65mm-85mm fpv micro quadcopter frame
New choice and best alternative motors of tiny whoop brushless version
Double E-clip design, prevent Motor bell to flying off. Good Dynamic balance
The upgraded 0802 19000KV brushless motors, insane power in tiny quadcopters

7. BETAFPV 4pcs 0802 19500KV Brushless Motors for FPV Racing Tiny Whoop 1S Brushless Drone Like Beta65 pro

Feature

Compitable droneBetafpv 0802 19500KV brushless motors is designed for 1s brushless whoop drone like Beta65 pro and Beta75 pro. It's too high for 2S battery, may burnt the ESC. For 2S drones, we recommend 0802 12000KV motor.
Flight timeThe flight time of 19500KV is 3 minutes, provides more power on throttle and better flight experience for indoor flight.
Weight only weighs 2.1g/pc, suitable for 31mm 4-blades 1.0mm shaft propellers.
ConnectorThis 19500KV motors is with Micro JST-1.25 3 pins connector plug. Supports 3.7-7.4V voltage.
PackageComes with 4pcs 0802 19500KV brushless motors and 8pcs M1.6 screws.

8. EMAX Tinyhawk 2.5" Freestyle BNF 2s FRSKY Outdoor Drone Carbon Fiber Quad for Beginners

Feature

The Tinyhawk Freestyle is the ultimate micro outdoor racing drone designed for beginners and experienced pilots alike.
Brushless Motor for Power: Utilizing a unique power system consisting of an all-new 1103 brushless motor paired together with the AVAN Rush 2.5 inch propeller, the Tinyhawk Freestyle offers unparalleled execution in thrust, control, and flight time.
Dual Battery Connector: Pilots can use two Tinyhawk batteries simultaneously in order to increase the voltage and overall power output for outdoor performance with flight times about 8 minutes.
EMAX Tiny receiver compatible with Frsky remote control D8/D16 mode. Fast F4 Processor for smooth stable flight characteristics 600TVL CMOS Camera included for fun FPV flight.
Aerospace Grade Carbon Fiber Material: The body frame features a newly designed aerospace grade carbon fiber, ultimate durability while maintaining minimal weight is achieved.

9. BETAFPV Meteor65 Acro 1S Brushless Whoop Drone Frsky with 19500KV 0802 Motor BT2.0 Connector F4 1S Brushless FC Micro Tiny Whoop FPV Acro Whoop Drone

Feature

BT2.0 ConnectorThe Meteor65 1S whoop drone comes with BETAFPV exclusive designed BT2.0 connector, which can support 9A continuous current and 15A burst while the PH2.0 connector just supports 4.5A continuous current. Solving the low voltage warning issue of PH2.0 connector on 1S brushless whoop when you start flying
19500KV 0802 Motor&31mm PropsEquipped with 0802 19500KV motor, the KV value is lower than racing version, which makes the flight time up to 4min. Suitable for both indoor and outdoor flight for beginners
F4 1S Frsky FC&M01 AIO CameraBETAFPV newest and lightest F4 1S brushless FC and M01 AIO camera. Its a perfect combo which has better performance on function for maximum weight savings
Meteor65 FrameNew marvellous design with 3.2g ultra lightweight. Compared to previous 65mm brushless frames, motor mounting position uses triangle bilateral stretch structure, makes frame more aesthetic. With the low profile of battery slot height, the drone's gravity center is reduced and improved the sense of compactness. It provides you more durable and smoother flight experience
Package&SupportComes with 1pc BT2.0 300mAh 1S lipo and 1pc BT2.0-PH2.0 adapter cable in default. Fot the Meteor65 Frsky binding step please check here: https://betafpv.freshdesk.com/support/solutions/articles/27000058401-how-to-bind-to-f4-1s-brushelss-fc-spi-frsky- Any problem please contact us via Email [email protected]

10. BETAFPV Meteor75 Frsky 1S Brushless Whoop Drone with F4 1-2S AIO FC BT2.0 Connector 1102 18000KV Motor M01 AIO Camera 25mW VTX for Tiny Whoop Micro FPV Racing Whoop Drone Quadcopter

Feature

BT2.0 ConnctorWith The BT2.0 connector, Meteor75 effectively decreases internal connector resistance for a much better discharge performance compare with initial PH2.0 connector
BT2.0 450mAh 1S BatteryMeteor75 is the first generation whoop powered by brand-new BT2.0 450mAh 1S batteryyou can get 3:00-4:00 flight time
1102 18000KV MotorsEquipped the latest 1102 18000KV motors and 40mm 3-blade props, which provides pilots stronger experience of a powerful outdoor flight like a 2S whoop drone
F4 1- 2S AIO FCWith the high performance STM32F411 processor 1-2S AIO FC boards and betaflight_matekf411rx_4.0.0 (Development Version), pre-soldered the BT2.0 cable, which can provide more stable and powerful 9A continuous current
Weight&PackageWeight 28.7g. The package comes with 1*BT2.0 450mAh 1S lipo and 1*BT2.0-PH2.0 adapter cable. The adapter cable is convenient for charging BT2.0 battery with your stock PH2.0 charger

Conclusion

All above are our suggestions for brushless tiny whoop. This might not suit you, so we prefer that you read all detail information also customer reviews to choose yours. Please also help to share your experience when using brushless tiny whoop with us by comment in this post. Thank you!