When you looking for cross hatch, you must consider not only the quality but also price and customer reviews. But among hundreds of product with different price range, choosing suitable cross hatch is not an easy task. In this post, we show you how to find the right cross hatch along with our top-rated reviews. Please check out our suggestions to find the best cross hatch for you.
Best cross hatch
Rank
Product Name
Score
Related posts:
Best cross hatch reviews
1. TOPCHANCES Hot Cross Hatch QFH Adhesion Tester Instruction Cross-Cut Tester Kit USG
Feature
This instrument and is designed and manufactured according to the standard of ISO2409-1992. Applicable to GB /T9286-98, BS 3900E6/ASTM D3359. The instrument draw the grid of a certain size by a certain specification of the tools by using the uniform force,cut and penetrate the coating to be a grid lattice graphics, to evaluate the adhesion of coating on the substrate through the assessment of the full extent of the grid.Uses :The instrument is mainly suitable for organic coating adhesion assay Hatch. Applies not only to the laboratory,the construction site can also be used under various conditions.
Working principle and scope :The instrument is a certain specification tool that will make the coating lattice graphics cut and penetrate,hatch completed by six graphic classification, assess the effect of the coating adhesion separated from the substrate.
Technical Specification :1.Multi-blade cutter spacing are: 1+0.01mm, 2+0.01mm. 2.Multi-blade cutter addendum straightness were: 0.003mm0.006mm. 3.Multi-blade cutter working tooth tip width: 0.05mm.
Description
Instruction:1.The specimen must be prepared according to ISOR1514 and ISO2828 requirements.
2.The test piece is placed on the tablet hardness sufficient.
3. Handheld Hatch handle, so multi-blade cutter perpendicular to the specimen plane.
4.With uniform pressure, steady approach does not vibrate and 20-50mm / S cutting speed cutting program.
5.The specimen is rotated 90 degrees on the cutting stroke cuts repeat the above operation,so as to form a lattice graphics.
6.With a soft bristle brush on both sides of the diagonal lattice pattern gently back 5 times.
5 times forward brush specimens.
7.The test at least at three different locations on the test piece is completed,if the test results of three different positions, the experiment should be repeated at more than three positions, all while recording the results.
To replace the multi-blade cutter, use a screwdriver blade Loosen the two screws, put the knives, knife blade attached to the handle side of the site, and tighten the screws.
Please Attention:
1.All cuts should be through the coating, but not too deep cut substrates.
2.As a result of the coating is too thick and hard and can not penetrate the material in the end,the experiment is not valid, but it should be stated in the test report.
3.The test must be a US company 3M tape produced 610-1PK special tape test(or otherwise specified test tape). The tape posted on the whole cross hatch, and then tore off the minimum angle, the result may be in proportion to the gum off the area determined according to the film surface.
4.The test should be carried out at a temperature of 23 2 and relative humidity of 50 5%.
Package Included:
1 x Brush
3 x Blades( 1 x 1mm 11 teeth1 x 2mm 11 teeth13mm 6 teeth)
1 x Cross Hatch Cutter
1 x Magnifier
1 x Carry Box
1 x1 roll of 3M Transparent Tape
2. top-tool Newest Cross Hatch Adhesion Tester Cross-Cut Adhesion Tester Kits with 1mm/2mm/3mm Blades, Magnifier, Handle, Brush and 3m Tape
Feature
Multi-blade cutter spacing are 1+0.01mm, 2+0.01mmMulti-blade cutter addendum straightness are 0.003mm0.006mm
Multi-blade cutter working tooth tip width are 0.05mm
The instrument is mainly suitable for organic coating adhesion assay hatch
Applies not only to the laboratory, the construction site can also be used under various conditions
Description
Newest Cross Hatch Adhesion Tester Cross-cut Adhesion Tester Kits with 1mm/2mm/3mm Blades, Magnifier, Handle, Brush and 3m TapeApplication:
This instrument with a certain specification, coating matrix graphics cutting and penetrate, row, complete graph according to the six levels of classification, evaluation of the separation of the coating from the substrate adhesion effect.
Operation:
1. You must use it by ISOR1514 and ISO2828 standard
2. Put the specimen on Hard enough plane
3. Use the handle Specimens cutting knife is perpendicular to the plane
4. Uniform pressure, with 20 to 50 mm/s cutting speed cutting
5. Specimen rotate 90, Repetitive movements of step (4)
6. Brush the specimen 5-10times with Soft brush
7. Specimens need to be finished in at least three different position
Adhesion Test Class:
SO Class ASTM Class Test Results Peeling area ratio(S)
0 5B The incision edges are smooth, without any peeling S=0%
1 4B The incision at the crossing of minor peeling 0S5%
2 3B The incision edge and the crossing of a small piece of peeling 5%S15%
3 2B The incision edge and the crossing of a piece of peeling 15%S35%
4 1B The incision edge and the crossing of large piece of peeling 35%S65%
5 0B The incision edge and the crossing of a large piece of major peeling 65%S
Includes:
1 x Brush
3 x Blades( 1pcs 1mm 11 teeth,1pcs 2mm 11 teeth, 1pcs3mm 6 teeth)
1 x Cross Hatch Cutter
1 x Magnifier
1 Roll of 3M Transparent Tape
1 x Carry Box
3. 3-in-1 Rotating Cross Hatch Adhesion Tester Cross-Cut Tester Kit with 1/mm/2mm/3mm blades, metal handle
Feature
1 The instrument is designed and manufactured according to the standard of ISO2409-19922 Used in GB/T9286-98, BS 3900 E6/ASTM D3359
3 Standard tool 3-in-1 Rotating Cross Hatch Adhesion Tester Cross-Cut Tester Kit with 1mm/2mm/3mm blades
Maybe you need to use Pencil Hardness Testerhttps://www.amazon.com/dp/B077G2D37Z
Maybe you need to use Matching bladehttps://www.amazon.com/dp/B072JK6CDD
Description
Technical Specification:1Multi-blade cutter spacing: 1 +0.01mm, 2+0.01mm.3+0.01mm.
2Multi-blade cutter addendum straightness: 0.003mm 0.006mm.
3Multi-blade cutter tooth tip width: 0.05mm.
4 Cutter spacing and cutter types: 1mm and 2mm with 11 teeth 3mm with 6 teeth
1.Placing the test piece on a tablet of sufficient hardness.
2.Holding the handle of the program grid, keeping the multi-blade cutter perpendicular to the plane of the test piece.
3.By using the uniform force, with the manner of not fibrillation and balance and 20-50mm/S cutting speed to draw.
4.Rotating the test piece to 90 , repeating the above operations, so as to enable to cut a grid lattice graphics.
5.Brushing the two diagonals of grid lattice graphics by using the soft brush gently backward and forward each five times.
6.The test should be taken at least in three different locations on the test piece. If the results of three positions are
different,the test should be repeated in more than three positions, and record all results.
7.If it need to replace the multi-blade cutter, use the screwdriver to unscrew the two screws on the cutter body and change the
cutter, affix the edge of cutter to the handle, then tighten the screws.
Note:
1. All the incision should penetrate the coating, cut into the substrate but must not be too deep.
2. If the coating is too thick and hard to penetrate in the substrate, then the test is invalid.However,
it should be explained in the test report.
3. In some special situation or special requirements, it must be compatible with the tape method for the final determination.
The tape is generally 12.7mm wide translucent tape, back material is polyester film or cellulose acetate.
4. Cross Hatch Adhesion Tester Cross-Cut Tester Kit, Multi-blade cutter spacing: 1 +0.01mm, 2+0.01mm
Feature
Multi-blade cutter spacing: 1 +0.01mm, 2+0.01mmMulti-blade cutter addendum straightness: 0.003mm 0.006mm.
Multi-blade cutter tooth tip width: 0.05mm.
Cutter spacing and cutter types: 1mm and 2mm with 11 teeth
Temperature: 23 2 C; Relative humidity: 50 5%.
Description
The product usually takes 6--13 business days to arrive to your hand after your order is confirmedPlacing the test piece on a tablet of sufficient hardness. Holding the handle of the program grid, keeping the multi-blade cutter perpendicular to the plane of the test piece. By using the uniform force, with the manner of not fibrillation and balance and 20-50mm/S cutting speed to draw. Rotating the test piece to 90 , repeating the above operations, so as to enable to cut a grid lattice graphics. Brushing the two diagonals of grid lattice graphics by using the soft brush gently backward and forward each five times. The test should be taken at least in three different locations on the test piece. If the results of three positions are different, the test should be repeated in more than three positions, and record all results. If it need to replace the multi-blade cutter, use the screwdriver to unscrew the two screws on the cutter body and change the cutter, affix the edge of cutter to the handle, then tighten the screws. Note: All the incision should penetrate the coating, cut into the substrate but must not be too deep. If the coating is too thick and hard to penetrate in the substrate, then the test is invalid. However, it should be explained in the test report. In some special situation or special requirements, it must be compatible with the tape method for the final determination. The tape is generally 12.7mm wide translucent tape, back material is polyester film or cellulose acetate. Put the tape over the whole grid, then tear off it at the minimum angle, the result can be obtained according to the film surface by adhesive peeling area ratio. Package: 1 x Carrying case 1 x Cross Hatch Cutter & Handle 1 x 1 roll of 3M Transparent Tape
5. Herschel Dawson Backpack, Black Crosshatch, Small 13L
Feature
Signature striped fabric linerInternal zippered pocket
Adjustable drawcord closure
Light back padding
5.875x8.75x13.5
Description
Pairing compact elegance with a timeless mountaineering style, the Dawson x-small backpack is equipped with functional storage options and slender shoulder straps.6. Cross Hatch Cutter Hot Cross Hatch Adhesion Tester Instruction Cross-Cut Tester Kit Coating Adhesion Test Instruction Cross-Cut Tester Kit 3PCS 1/2/3mm Teeth Knife Blades
Feature
Multi-blade cutter spacing: 1 +0.01mm, 2+0.01mm. 3+0.05mm. Cutter spacing and cutter types: 12mm with 11 teeth and 3mm with 11 teethMulti-blade cutter addendum straightness: 0.003mm 0.006mm.
Multi-blade cutter tooth tip width: 0.05mm.Temperature: 23 2 C; Relative humidity: 50 5%.
Maybe you need to use Matching bladehttps://www.amazon.com/dp/B072JK6CDD
Maybe you need to use Pencil Hardness Testerhttps://www.amazon.com/dp/B077G2D37Z
Description
1.Placing the test piece on a tablet of sufficient hardness.2.Holding the handle of the program grid, keeping the multi-blade cutter perpendicular to the plane of the test piece.
3.By using the uniform force, with the manner of not fibrillation and balance and 20-50mm/S cutting speed to draw.
4.Rotating the test piece to 90 , repeating the above operations, so as to enable to cut a grid lattice graphics.
5.Brushing the two diagonals of grid lattice graphics by using the soft brush gently backward and forward each five times.
6.The test should be taken at least in three different locations on the test piece. If the results of three positions are
different,the test should be repeated in more than three positions, and record all results.
7.If it need to replace the multi-blade cutter, use the screwdriver to unscrew the two screws on the cutter body and change the
cutter, affix the edge of cutter to the handle, then tighten the screws.
Packing List
1 3PCS knife blades (1mm11 teeth, 2mm11teeth , 3mm 11teeth )
2 3M tape (19mm * 32.9m),
3 magnifying glass-1 ,
4 wrench-1,
5 a brush-1 ,
Note:
1. All the incision should penetrate the coating, cut into the substrate but must not be too deep.
2. If the coating is too thick and hard to penetrate in the substrate, then the test is invalid.However,
it should be explained in the test report.
3. In some special situation or special requirements, it must be compatible with the tape method for the final determination.
The tape is generally 12.7mm wide translucent tape, back material is polyester film or cellulose acetate.
Put the tape over the whole grid, then tear off it at the minimum angle,
the result can be obtained according to the film surface by adhesive peeling area ratio.
7. CGOLDENWALL Cross Hatch Adhesion Tester Cross-Cut Tester Kit Cross cutter Multi-blade cutter spacing: 1 +0.01mm, 2+0.01mm
Feature
Multi-blade cutter spacing: 1 +0.01mm, 2+0.01mmMulti-blade cutter addendum straightness: 0.003mm 0.006mm.
Multi-blade cutter tooth tip width: 0.05mm.
Cutter spacing and cutter types: 1mm and 2mm with 11 teeth
Temperature: 23 2 C; Relative humidity: 50 5%.
Description
The product usually takes 6--13 business days to arrive to your hand after your order is confirmedperation and user instruction:
Placing the test piece on a tablet of sufficient hardness.
Holding the handle of the program grid, keeping the multi-blade cutter perpendicular to the plane of the test piece.
By using the uniform force, with the manner of not fibrillation and balance and 20-50mm/S cutting speed to draw.
Rotating the test piece to 90 , repeating the above operations, so as to enable to cut a grid lattice graphics.
Brushing the two diagonals of grid lattice graphics by using the soft brush gently backward and forward each five times.
The test should be taken at least in three different locations on the test piece.
If the results of three positions are different, the test should be repeated in more than three positions, and record all results.
If it need to replace the multi-blade cutter, use the screwdriver to unscrew the two screws on the cutter body and change the cutter, affix the edge of cutter to the handle, then tighten the screws.
Note:
All the incision should penetrate the coating, cut into the substrate but must not be too deep.
If the coating is too thick and hard to penetrate in the substrate, then the test is invalid.
However, it should be explained in the test report. In some special situation or special requirements, it must be compatible with the tape method for the final determination.
The tape is generally 12.7mm wide translucent tape, back material is polyester film or cellulose acetate.
Put the tape over the whole grid, then tear off it at the minimum angle, the result can be obtained according to the film surface by adhesive peeling area ratio.
Package:
1 x Carrying case
1 x Cross Hatch Cutter & Handle
1 x 1 roll of 3M Transparent Tape
8. Hot Cross Hatch Adhesion Tester Instruction Cross-Cut Tester Kit Multi-blade cutter spacing: (2mm 11 teeths)
Feature
There are 6 kinds of types of the cutting blades, ,The price is each kind of the blade,not all the blades.1mm 6 teeths ,2mm 6 teeths ,3mm 6 teeths
1mm 11 teeths,2mm 11 teeths,3mm 11 teeths
This price only for one kind of blade, only 1 of blade.
The price is only for one blade!
Description
High precise Cross Hatch Adhesion Tester blade,Cross-Cut Tester bladeThere are 6 kinds of types of the cutting blades:
The price is each kind of blade, not all the blades,you should tell us which kind you want to buy. cutter spacing & No. of teeth
1mm 6 teeths
2mm 6 teeths
3mm 6 teeths
1mm 11 teeths
2mm 11 teeths
3mm 11 teeths
9. Baby Boom Cross Hatch Backpack Diaper Bag
10. Nautica Men's Straight Light Cross Hatch Jean, Sand wash, 38W 32L
Feature
Straight fit jeans with five-pocket styling and a light blue wash.Straight fit: sits low on the waist, cut straight through the seat and thigh, straight leg; approx. Inseam: 30", 32", 34"
Belt loops; logo patch on back waistband
